If your car's knock sensor is malfunctioning, it could be due to low oil levels. The knock sensor is responsible for detecting engine knocking and adjusting the ignition timing to prevent it. If there's not enough oil in the engine, the knock sensor won't be able to do its job properly.
No, you cannot run a car with no knock sensor. The knock sensor is responsible for detecting engine knocking and sending a signal to the engine control unit to adjust the ignition timing to prevent engine damage.
The knock sensor is designed to detect engine knocking and send a signal to the engine control unit. This helps the ECU to adjust the ignition timing to avoid engine damage. However, if the knock sensor is not working properly, it can cause the engine to idle poorly.
5/5
Fits Lexus ES300 2000-2003; GS300 2005; IS300 2001-2005; SC300 1994-2000; RX300 2000-2003; RX330 2004-2006
Fits Toyota Avalon 2000-2004; Camry 1999-2006; Celica 2000-2002; Highlander 2001-2004; Sienna 2000-2003; Solara 1999-2003
$234
Installing aftermarket components on a Toyota with which I've had trouble in the past gave me some cause for concern. This 2002 Avalon has no longer displayed the check engine light after I fitted the knock sensors and harness. For less than one-fourth the cost of dealer parts.
4.7/5
Quality construction
Excellent quality and material
Exacting tolerances
Application specific to ensure a correct fit for your vehicle
Matches OE form, fit, and function
Includes corrosion resistant terminals and coatings
Constructed to withstand a harsh underhood environment
Sensor is mounted in cylinder block
$234
Dear Amazon, I just wanted to provide a positive review of this knock sensor. Beck Arnley components have always been reliable to me. For my 2004 Honda CRV, I buy only high-quality parts. Still drives like new after 186,000 miles. With this review, I hoped to repay the Amazon Community for everything they've done for me. As a result, I have a few suggestions for any beginners out there trying to complete the work themselves. 1 Before attempting to separate the electrical clip from the old K sensor, thoroughly spray it with electrical cleaner. 2 Use an electrical cleaner spray to clean the connector's interior before reconnecting the new K sensor. 3 New K sensors shouldn't be tightened any more than you would a mountain bike tire to a "nice and tightly snug" condition. I used the wrench you can see in my photos and completed the task in about an hour and a half. The old knock sensor can be unscrewed once it has been loosened if you have a smaller hand and can reach up between the starter and manifold. With my feet on the front tire of the driver's side vehicle and my left hand free, I kind of pushed my body up to get my arm up there. I'm a little small, and the car was on jack stands as well. I'm explaining this because, for whatever godawful reason, I was completely unable to get my right arm up there. And while I was inside the car, there were times and places when I didn't think it was even feasible to manually remove the old knock sensor! So if you're attempting to accomplish something yourself, bear that in mind. Since "Knock Sensors Rarely Go Bad On These Hondas," according to numerous web accounts, the knock sensor might be anything else, I say BULL and recommend changing the sensor to ensure that the check engine light is turned off. In order to save money by doing your own job instead of paying a mechanic who is attempting to enjoy a great holiday with your hard-earned money, I hope I have helped someone out there. Or charging you $100 for a task that they can complete in five minutes. What companies generally charge customers these days is regrettable. Keep in mind that nothing can ever be taken from you. And believing is knowing. My brothers and sisters, have faith and KNOW GB.
4.7/5
12601822 WIRE 2.480
$234
An pricey gadget for what it seems to be, but I wouldn't replace knock sensors any other way because it takes so much time and is so laborious. I thought about using the old knock sensor wiring harness, but I'm glad I got the new one in addition to the sensors because one of the old sensor nipples broke off in the old harness when I removed it. If I had tried to save money for what turned out to be a full weekend's worth of work in replacing sensors, I would have kicked myself. With the additional sensors and wires, the wiring harness is a high-quality product, and the car performs significantly better on hills and under load.
4.5/5
12601822 WIRE 2.480
$234
This is a great harness, which I used when I chose to replace the knock sensors while I was changing my oil pressure sensor. I don't worry that water will leak underneath it, and I didn't RTV-seal my knock sensors either. Unless you don't use the foam cushions underneath your intake manifold, which you should because it is their intended usage, you are not need to. This has seen a lot of use and is flawless; there are no problems, and it fits exactly like the original. Nice part, great purchase!
4.2/5
This Ignition Knock Detonation Sensor is especially designed for Acura RL 3.5L 1996-2004 Honda Civic 1.6L 1996-2000.
Compatible OEM part number of this Ignition Knock Detonation Sensor are 30530P2MA01, 30530-P2M-A01, 30530-PV1A01, 213-2308, KS65, 5S2308, SU4778.
ââ²ââ²ââ²ââ²If you buy a wrong type for your vehicle, please not damage the ââ²label and barcodeââ² return it in the original package. If you have installed, please clean it and put into the resellable original package otherwise Amazon may not accept your returns.
ââ²ââ²ââ²Please carefully check your vehicle year/make/model with our description ââ²Amazon fitment and Advertisement are not final standards ââ²You should read our description carefully, and it will tell you more about the fitment. In addition, you can compare them with pictures first.
ââ²ââ²ââ²Thanks for your encouraging review and feedback! It really increases our service level and passion of work! Incase you meet problem with our products, please contact us first before you give feedback and review. We will assure you will get the best solution and service. ââ²THANK YOU!
$234
On my 2000 Civic EX, I had the P0325 error code. I've read that purchasing a non-Honda part won't solve the problem. The code has been turned off so far, and I don't anticipate it returning. Now a few weeks have passed.Given the extremely harsh conditions where the sensor and harness are housed, I assume those who are experiencing problems are actually dealing with wiring problems rather than problems with the sensor itself.
4.2/5
Fitment Below
Ships from Wisconsin!! 1 Year Warranty
VOTEX Nissan Knock Sensor - Part Number 22060-30P00
Let us Save YOU $$ Over your Local Dealer!
100% Satisfaction Guarantee, Period!
$234
I purchased this to replace the KA24DE knock sensor in my 240sx, which was beyond repair. I discovered that the overheating problem with the car was caused by the timing being significantly advanced. I replaced this in the hopes that the timing advance would be caused by the sensor not reading knock because I was already beneath the intake dealing with the effects of my overheating problem. Although I was unable to determine whether the sensor was the problem, I have been using it for roughly 300 miles and have never experienced a problem with timing moving too far. On a turbocharged engine, where you have to be extremely careful to avoid knock, I might be hesitant to use this sensor, but you can use a NA engine with confidence. I'm definitely content.
3.5/5
ââ²ââ²ââ²Thanks for your encouraging review and feedback! It really increases our service level and passion of work! Incase you meet problem with our products, please contact us first before you give feedback and review. We will assure you will get the best solution and service. ââ²THANK YOU!
ââ²ââ²ââ²Please carefully check your vehicle year/make/model with our description ââ²Amazon fitment and Advertisement are not final standards ââ²You should read our description carefully, and it will tell you more about the fitment. In addition, you can compare them with pictures first.
This Ignition Knock Detonation Sensor is especially designed for Acura RDX 2008-2012 RSX 2002-2006 TSX 2004-2007 Honda Accord 2003-2007 Civic 2002-2005 CR-V 2002-2009 Element 2003-2011.
ââ²ââ²ââ²ââ²If you buy a wrong type for your vehicle, please not damage the ââ²label and barcodeââ² return it in the original package. If you have installed, please clean it and put into the resellable original package otherwise Amazon may not accept your returns.
Compatible OEM part number of this Ignition Knock Detonation Sensor are 30530-PPL-A01, 30530PPLA01, 30530-PNA-003, 30530PNA003, KS197, SU6143, 5S2320, 1580917.
$234
For my Ford truck, the knock sensor is a great deal. also quick shipment.
3/5
âÅâãâ¬ÂWARRANTY OFFERãâ¬â30 Days Money back Guarantee.We provides 18-Month worry free warranty for our Product. Please contact us before if have any problem.
âÅâãâ¬ÂSENSOR LOCATIONãâ¬âThe Knock sensor is located on the engine block and in some applications under the intake manifold
âÅâãâ¬ÂWHAT YOU GET ãâ¬â1PC KS197 Knock Sensor.
âÅâãâ¬ÂOEM PART NUMBERãâ¬â30530-PPL-A01, 30530PPLA01,30530-PNA-003 ,30530PNA003,KS197
âÅâãâ¬ÂCOMPATIBLE ãâ¬âAcura RDX (2012-2007) Acura RSX (2006-2002) Acura TSX (2008-2004)Honda Accord (2007-2003)Honda Civic (2005-2002) Honda CR-V (2009-2002)Honda Element (2011- 2003)
$234
I purchased this from Amazon. It arrived in its original box and was covered in plastic, however the plastic was little dusty and stretched from a garage. Two months ago, I installed some on my truck, and they are without a doubt the best product I've ever installed. These are what my f150 has, and I genuinely wouldn't buy anything else. Please note that I am aware that there are better products available at significantly higher prices, but I am not a race car driver on a closed course, and neither are half the people who run them, so that's their choice. However, for my money, I refuse to buy off-brand junk or really expensive items that gained their reputation by spending money on advertising rather than research. Instead, I usually opt for mid-priced items like these, and I think these are a real find.
2.9/5
OEM Fit, Quality, Finish ---- This nock sensor and harness kit has gone through rigorous test for perfect fit and function that exceeds OEM specifications, which is why the company covers them with a limited lifetime replace or return commitment against any defects in materials and workmanship.
Knock Sensor w/ Harness Kit ---- Replace the factory knock sensor and harness kit (The engineââ¬â¢s knock sensor (or sensors) detects preignition and detonation, potentially damaging forms of abnormal combustion. Though full-blown knocking and pinging are audible to the human ear, the knock sensor detects imperceptible levels. When knocking is detected, the engineââ¬â¢s computer can retard the spark plug timing to prevent it.)
Fits These Vehicles ---- Works on many GM models, such as: Buick Rainier | Cadillac, Cts, Escalade | Isuzu Ascender | Pontiac Firebird, GTO | Chevrolet Avalanche 1500, Camaro, Corvette, Express 1500, Express 2500, Express 3500, Silverado 1500, Silverado 2500, Silverado 3500, Sonora, SSR, Suburban 1500, Suburban 2500, Tahoe, Trailblazer | GMC Envoy, Savana 1500, Savana 2500, Savana 3500, Sierra 1500, Sierra 2500, Sierra 3500, Yukon | Hummer H2
Replace Part # ---- Will replace the original part 12601822, 12589867, 81045-66030, 10456603, 213-3521, 917-033 on various 1999-2007 Chevrolet Silverado 1500, 1999-2008 Chevrolet Silverado 250, 2001-2008 Chevrolet Silverado 3500
All-in-one Kit ---- Includes everything you need for a fast & effective replacement of knock sensor & harness kit on the engine monitoring system, comes with 2 knock sensors, 2 harness kits, 1 operation manual for easy installation.
$234
It worked perfectly; my 5.3 stopped making any pinging noises or having knock sensor errors.
Detonation is a knocking noise that you'll hear coming from your engine. It's caused by the air/fuel mixture in the cylinders detonating too early. This can be caused by a few different things, but the most common cause is using lower octane fuel than what your car requires. If you're using the correct fuel and you're still hearing detonation, there are a few other things you can check. First, make sure your spark plugs are in good condition. Old or fouled spark plugs can cause detonation. Next, check your engine's timing
It usually takes about two hours to replace a knock sensor. This includes time to remove the old sensor and install the new one.
There are two knock sensors on most engines. One is located on the front of the engine near the cylinder head and the other is located on the back of the engine near the firewall.
If your car is experiencing knocking or pinging sounds, especially when under load, it may be time to install a knock sensor. Knock sensors are designed to detect these sounds and send a signal to the engine control unit to adjust the timing. This can help prevent engine damage caused by knocking. The cost of a knock sensor will vary depending on the make and model of your car. Expect to pay between $100 and $200 for the sensor itself, plus labor costs of around $100.
The knock sensor is a vital part of the engine management system, and it is responsible for monitoring engine noise. If the knock sensor detects knocking, it will send a signal to the engine control unit (ECU) to adjust the ignition timing. How often you need to replace the knock sensor depends on the make and model of your vehicle, as well as your driving habits. However, it is generally recommended that you replace the knock sensor every 30,000 miles or so.
A knock sensor is worth replacing if your car is knocking. A knock sensor is a sensor that detects knocking and sends a signal to the engine computer to adjust the timing to prevent engine damage.
COPYRIGHT © 2019