There are a few things you can do to fix a recliner problem. First, check to see if the recliner is still under warranty. If it is, you may be able to get it repaired or replaced for free. If the recliner is not under warranty, you may be able to fix it yourself by following the instructions in the owner's manual. If you cannot find the owner's manual, you can usually find it online. If you still cannot fix the problem, you may need to call a professional furniture repair person.
To identify your recliner, first look for a label or tag that indicates the manufacturer. If you cannot find a label, look for any identifying marks or symbols on the chair. If you still cannot identify the chair, take a picture of it and bring it to a furniture store or an antique store.
If your recliner has a footrest that won't stay up or is sagging, there are a few things you can do to fix it. First, check to see if the footrest is properly aligned. If it is not, you can try adjusting it. If that doesn't work, you can try tightening the screws that hold the footrest in place. If the footrest is still not staying up or is sagging, you may need to replace it.
If your recliner won't stay reclined, there are a few things you can try to fix the problem. First, check to make sure that the recliner is not locked in the upright position. If it is, unlock it and try reclining again. If the recliner still won't stay reclined, try adjusting the backrest tension. Most recliners have a knob or lever that you can use to adjust the tension. If adjusting the tension doesn't work, try reclining the chair all the way back and then sitting up quickly. This should release the tension and allow
5/5
Easy to install 2 Button Round Style Handset with 5 Prong Plug
4.8ft length Recliner Switch Cable
You can use on many different brands of recliners and lift chairs that use the 5 pin round plug
Okin 2 Button Round Hand Control Handset
Works with Okin, Dewert, and Limoss Motors commonly found in Power Recliners
$234
This switch was exactly what I needed to fix the leg lift on my sectional couch. It was a much simpler and less expensive remedy than having to replace the motor, which would have been okay. It cost roughly $12. The chord on this switch is a tiny bit shorter than it was on the old device, but it's not a significant worry and it only needed some little rerouting to shorten the path. The connection fit into place without any issues, and the mounting holes for the screws lined up exactly with the pre-drilled holes in the previous connector. The colour also matched. With simply a Phillips screwdriver, installation is simple. Little more to add.
4.9/5
The release lever handle can fit most popular reclining sofas and chairs.
Please Note:This Recliner Replacement handle doesn't included the cable.
It is made of aluminium alloy and with high quality.
It is durable, easy and friendly to use.
$234
Why on earth would furniture makers attach plastic locks to such obscenely costly couches? About a year ago, one of the plastic locks on our couch totally split in two, rendering it useless. Therefore, we had only been able to use one of the couch's reclining sides, which we had spent a lot of money on. Although we had thought about phoning the furniture firm to arrange for a repair, we decided against it because of the outrageous cost involved. Thank goodness I found this item on Amazon! Two new latches for the price of one are made of metal, not plastic. I wasn't entirely sure they would fit our couch, but I reasoned that the pricing made it worthwhile to take the chance; if not, Amazon offers a simple return policy. Everything literally only took a few minutes to fix, and it now functions perfectly! The metal locks shouldn't break, so they're actually better than new! I appreciate you providing this goods.
4.8/5
Input: AC 100-240V,1.5-2.0A 50/60Hz. Output :DC 29V/24V 2.0A. Volt and current adjust auto, If the plug of transformer could fit with your recliner socket so it can work
NOTICE: Power cord is included. Update the Magnet Ring, no radiation and longer life time.
ALMOST COMPATIBLE WITH ALL BRAND RECLINER : Recliner power adapter fully Compatible with OKIN, Limoss, ashley and Tranquil Ease Lift Chair,Cheers electric sofa. DeltaDrive and BetaDrive Motors. It almost compatible with all recliner and sofa in the market.
ALMOST COMPATIBLE WITH ALL MODEL: If the connection(flat & round) is same with your recliner so it can work. Power recliner transformer compatible with Part Numbers(include but are not limited): ZBHWX-A290020A,W52RA73-290018, HXY-270V2220A, KDDY001B, KDDY008, ZB A290020-B
WARRANTY :12 months warranty, 30 days money return gurantee, 24*7 email support.
$234
I believed they were toast when a powerful lightning storm destroyed two electric power recliners along with other electrical appliances in our home. I did some research and found the Ponkor Universal Power Supply on Amazon. Great ratings, and some even experienced the same thing as me when their power recliners were destroyed by lightning! I figured I'd try it out for less than $30 for two. On one of the seats, I made sure the new adaptor and the chair had the same plug configuration. decided to try the other chair. And lo, both chairs were functional! Amazingly, this tiny $15 component got the job done! I, a 65-year-old woman, was able to complete everything by herself. Flipping the chairs over was the hardest part!
4.8/5
Total Cable Length Excluding Handle and Z Tip: 35"
To get the Correct Size, Read Below Section "Getting the Size You Need"
Exposed Cable Length (Length from Plastic Plug to end of Z Tip): ~5.5"
This product is suitable for most of the furniture brands, but not all the brands. Purchased customer feedback such as Raymour & Flannigan, Rooms Go, Conns's, Wickes, Bobs store, Bassett, etc.
Handle Size: 4-1/2" x 2-5/8"
$234
Like many others, I purchased some off-brand furniture and have discovered that the plastic chair handle eventually breaks. I bought this replacement component (after finding the right size and handle shape - look carefully). This one is entirely metal and operates flawlessly. Others claimed they had to drill holes; however, mine already had two sets of holes, probably because the screws are used in various locations depending on the type of furniture. The swap out was straightforward. Simply undo the screw, take out the old handle, connect the cable to the new handle, and tighten the screw. One piece of advice: 1) Don't worry about the angle of the screws when removing the handle. When you screw it back in, the holes are hidden by the fabric, making it impossible to see them. However, if you know how they were removed, you won't have any trouble putting them back in. 2) Once the cable has been released from the old handle, DON'T LET IT GO; otherwise, it will pull itself into the arm and be extremely difficult to remove. Remove the cord before attempting to change the handle because my replacement handle came with one attached. Additionally, there is a little wire clip that is easy to notice that holds the cable to the handle; remove it before you pull the cable free. Otherwise, a replacement is simple. The new handle appears to function more efficiently than the old one!
4.7/5
COMPATIBLE WITH : Switching power supply transformer fully Compatible with OKIN, Limoss and Tranquil Ease Lift Chair,Cheers electric sofa and Power Recline DeltaDrive and BetaDrive Motors with a two pin (flat & round) connection to the 2,motor.
PARAMETER: Input: AC 100-240V,1.5-2.0A 50/60Hz. Output :DC 29V 2.0A.
NOTICE: Power cord is included.
COMPATIBLE MODEL: Power recliner transformer compatible with Part Numbers: ZBHWX-A290020A,W52RA73-290018, HXY-270V2220A, KDDY001, KDDY008, ZB A290020-B
12 months return, 30 days refund, 24*7 email support.
$234
My Ashley power recliners were packaged with quite huge, hefty power supplies that protruded the prongs for the wall outlet. As a result, the second outlet of a wall outlet with two outlets was blocked by the unit. It is simple to plug two of these new units into a wall socket because they fit into a much smaller box that is in line with a power cord. Check your volts, amps, and the type of connector (zoom in on the picture) that goes to your chair if you replace your power units with these.
4.7/5
Medium length ( This is not a critical length). Length is 31".
Exposed length 4.75". Critical Length for the cable as long as this measurement is correct it will work regardless of recliner brand.
Heavy duty 6mm Barrel versus 3mm to prevent stripping and lasts longer.
This couch release handle will fit the most of brand and model furniture,such as Ashley, Lazy boy sofas, Glider, Rocker recliner chairs, loveseats , Lane couch and so on. With long end cable. And Easy to install.
Small over handle is 3.5" by 3". This handle with cable is a universal replacement parts found in Ashley furniture and most major recliner brands.
$234
*Update* The comments made about the tools are odd. To remove the old portion and attach the new one to the sides of the recliners, I just used a phillips head screwdriver. To remove the old part, I simply squeezed the tabs within the bottom of the chair with a set of wire cutters. I didn't require any more tools, and it works perfectly! It was really simple to replace this. So much so that after ordering one to test out, I went on to get another! Finding directions was challenging, and I had to wait a while before using common sense out of concern that I could accidentally crush my hand in the recliner. After I understood what I was doing, it was pretty easy. I recommend either including a link to a YouTube video for this particular model or even just basic directions on how to unlock the recliner. Others might initially worry as I did that I would tangle my hand during the release. (which, knowing what I know, was not likely to occur). Yet again, five stars! replaced in less than ten minutes.
4.7/5
29V 2A transformer with battery backup, motor cable and AC power cord
$234
Works well. Recliner wouldn't function properly, however it did operate extremely slowly on batteries, suggesting that the motor was likely in good condition. The chair's cord had no voltage when it was tested with a meter, and the motor made no noise. choose to take a $25 risk rather than replace a $600 chair. It appeared two days later, replete with a set of cords. It operates flawlessly after being plugged in. I glued a piece of paper with the ordering information to the new power supply in case I need it in five years if it happens again. I attached the new wires to the chair's frame underneath so I can find them if I need to. Again, Amazon triumphs.
4.7/5
This is not an OEM part, but the quality is much better. For any reason you're not completely satisfied, you can ask for a replacement or full refund
Exposed Length 4.75": Critical Length for the cable as long as this measurement is correct, it will work regardless of recliner brand
Medium Length: The recliner handle cable is not a critical length. Length is 37"
Small Oval Handle: Recliner release pull handle is 3.5" by 3", this handle is a universal replacement cable found in Ashley Furniture and most major recliner brands
Made of high quality materials, it is durable and has a long service life.
$234
As the chair was not reclining, I had a repairman offer to fix the snapped wire. When I finally thought of Amazon, these cords appeared. Outstanding value for only 15 minutes of effort. Check your draw handle if you're changing it as well, and make sure the tail is the proper length. There are variances and the handles on the chairs have specific apertures. This specific chair is a component of a Star Furniture home theater set. The cable tail (an exposed steel component) and the pull ring in the illustration both fit well. At the pull handle, I undid a Phillips head screw and made sure it was free. The recliner was then expanded by rolling the chair to its side and releasing the clasp on the bottom of the chair. Wait! The wire was free to pull from the top when the z-shaped end rose out. To fix the broken cable quickly, I devised the quick fix of tying a thick thread to that end, pulling the cable out while leaving the rope through the chair in its place. Pull out the old cable now, and then attach the string to the new cable by threading it through your chair. Work the z-shaped end back to the lock after gently pulling the string until you have the cable. Make sure there are no kinks in the run. Connect the z-shaped end and insert the plastic cable stopper (about 6 inches from where the plastic coating starts on the z shaped end). Reposition the chair and release the top latch. ought to be prepared to go. Hope this was useful.
4.6/5
[Universal Fit]- Keten replacement cords accommodate Most Strung Lounge Chair. Suitable for both Standard and XL size recliners from Faulkner, Lafuma, Caravan Sports, Xtremepower US, BestChoice products and etc.
[Convenient pack]- These laces can be rolled up easily and it will only occupy little space which is very easy for you to keep it and bring it with you when you go out for camping or fishing with your anti-gravity chair.
[What you get]- 2 long cords (86' /2.2m) and 2 short(59'/ 1.5m). Keten offers 45days 100% money back guarantee and Life-time warranty and we will help you solve your problem within24 hours. Keten recommends changing lacing every two years to maintain excellent comfort.
[Reliable quality]- This replacement cords are made of high-quality dichotomanthes rope, good elasticity, difficult to wear.
[Easy to install]- A pack of replacement cord includes a short lace and a long lace. The short lace can replace the part of upper part of the zero gravity chair and the long lace can replace the part of lower part of the zero gravity chair. With the instruction, it will be a very easy thing to repair your chair by yourself.
$234
These are what I bought for my XL gravity chair. They differed slightly in length from those seen in the store's advertising, where I purchased the chair. I chose the longer ones out of caution after reading the reviews on that website and Amazon. The lower ones are perfect for the chair. I simply doubled up on a few of the holes as the ones for the top of the chair were a little longer. The bungees on one side of the chair were broken, so I simply replicated the other side. The rest of them followed suit as I inserted the new bungee into the hole left by the old one and left. I don't think it took me an hour to do it because it was so simple.
3.8/5
*GUARANTEED* We offer only the best quality parts for Recliners, Sofas and Couches. 100% Satisfaction Graranteed.
*STURDY* Small Oval Style Recliner Handle made of High Quality Industrial Plastic, and packaged with shake-proof bubble plastic bag to prevent damage during transportation
*UNIVERSAL* This finger release style universal replacement handle Fits both 3mm and 6mm Cables (Car Door Flapper Style) Chair Release Handle for Sofa, Couch or Recliner, including power recliners
*Dimension*: Length: 3.7 inches, Width: 2.96 inches, whole Package consists of 2x Recliner Pull Handles
*High Quality* 100% Brand New & High Quality, fits both a 6mm and 3mm cable.
$234
Unbelievably, the man at the Ashley furniture store where we purchased the sofa indicated replacement parts aren't made for the recliners when we called about the broken handle on our sofa. He offered half-heartedly to search the warehouse for another sofa from which he could remove the handle. What a commotion! We won't be returning to that shop!These components were as stated and delivered swiftly. Our sofa's broken handle wasn't difficult to fix and didn't take long. However, the accompanying spring, which is the odd little bent paper clip-like object in the picture, was the incorrect size. Fortunately, we still had the first one and could use it.
There are several ways to manually open a recliner. One way is to find the release handle, which is usually located on the side of the chair near the armrest. Another way is to push down on the footrest while pulling up on the back of the chair.
To measure a spring for a recliner, you will need to know the width, length, and thickness of the spring. You will also need to know the weight of the person who will be using the recliner. To measure the width of the spring, you will need to measure the distance from the outside of the spring to the inside of the spring. To measure the length of the spring, you will need to measure the distance from the top of the spring to the bottom of the spring. To measure the thickness of the spring, you will need to measure the distance from the top
When a recliner breaks, the first thing you need to do is open the handle. This can be done by gently pulling on the handle until it comes off. If the handle is stuck, you may need to use a screwdriver to pry it off. Once the handle is off, you can access the mechanism that controls the recliner.
It typically costs between $150 and $300 to fix a recliner chair. The exact cost will depend on the type of damage and the severity of the issue.
It's generally considered a bad idea to let your feet hang over the edge of a recliner, since it can put unnecessary strain on your legs and back. Additionally, it can be dangerous if you happen to kick the footrest or lose your balance and fall off the chair. If you must let your feet hang over the edge, be sure to do so carefully and only for short periods of time.
The mechanism of a recliner is composed of several parts that work together to allow the chair to recline. The backrest is connected to the seat by a series of hinges, and the footrest is connected to the seat by a series of springs. The backrest and footrest are both supported by a frame that is mounted on the chair's base. The recliner mechanism is controlled by a series of levers and buttons that are located on the chair's armrest.
COPYRIGHT © 2019