4.5/5
Extra long gussets extend past the last mounting point for extra strength and durability
No Silicone Needed! Save 60% On Installation Time
10 Snow Guards, 10 Perfect Seal Gaskets, 30 Screws
Contoured joints for extra strength
Three #10 screws for secure mounting
$234
I discovered they are reasonably priced and really well designed after doing some in-depth research on snow protection devices. They operate very well and are quite simple to install. Amazing gasket design that is superior to silicon. They look fantastic and have incredible strength. They are hardly discernible on your roof up close, and they are completely invisible from a distance. If you compare these snow guards based on price and quality, they are the best available.
4.5/5
New
$234
I purchased this to have as a backup for a new-to-me Ultra Classic, but when I took off my Derby Cover, I saw that it was using a large flat washer that had a small amount of leakage. This gasket, like any other, was a little challenging to maintain in place during the reassembly process, but I'm ordering another to have on hand as a spare because, in my opinion, it's ideal.
4.4/5
Genuine Oem:Yes, Category 2:Steering Gear & Linkage, Fitment Footnotes:Parts Part Included With P/s Pump., Item Name:Inlet Connector Gasket
Brand:Honda, Fitment Type:Direct Replacement, Superseded Part Number:91345-PDA-E01, Category 1:Steering
Manufacturer Part Number:91345RDAA01, Category 3:Pump & Hoses, Other Part Number:91345-PDA-E01, 91345-PAA-A01
$234
When compared to going to the Acura dealer, this was obscenely overpriced—by a factor of ten. I have never spoken anything like that before. However, it was the ease of Amazon delivery.To stop the whine, some cars may also require a new power steering reservoir. They have a bottom-mounted plastic mesh filter that is difficult to clean and can clog, leading to oil shortage.The o-ring was rather simple to install. It's a complete disaster. Place many rags beneath the outlet. It's difficult to get in, but most people with hands that are medium in shape should be able to with enough patience. For the hose clamp, all you need are some pliers and a small 10mm wrench.
4.1/5
Seals irregular surfaces and large clearance areas with a tough elastic film.
Solvent based for easy removal. Effective from 40 degrees F to 300 degrees F. 3.5 oz. (99 grams)
Genuine Honda Product, OEM Part Number: 08717-1194
For use in areas not requiring solid gaskets. Also can be used to reinforce conventional gaskets.
Resists gasoline, oil, water and most chemicals. Resists pressure and vibration.
$234
NEVER EVER RETURNING TO ANY OTHER SEALANT. THIS IS THE STUFF THAT IS CALLED OUT ON A GASKET.By the way, TAKE NOTE!LISTEN TO ME NOW, TRUST ME LATER!THE OPEN OR POT TIME IS RATHER SHORT SO ASSEMBLY PREPARATION AND PERHAPS A DRY/MOCK RUN (NECESSARY FASTENERS HAND TOOLS GASKET DOWEL LIGHTING IN OR NEAR POSITION IN PROPER ORDER ETC) BECOME VERY IMPORTANT....REMOVING THIS SEALANT IS NOT SOMETHING YOU WANT TO DO. IF YOU'RE NOT GOING TO STAY WITHIN GUIDELINES, OR IF YOU'RE NOT COMPLETELY READY FOR FITTING, OR IF YOU NEED A 30 MINUTE POT TIME, WHAT SHOULD YOU DO? LEAVE THIS FACTORY PROFESSIONAL PRODUCT FOR THE DEALERSHIP AND JUST GET WHAT YOU KNOW.
3.9/5
The best Vision Grill gasket that we sell!
1 x 1/4 x 15' Vision Kamado gasket
Guaranteed LavaLock performance
Correct size gasket for Vision Grill
Extra material FREE.
$234
My Vision's original factory seal, which lasted roughly a year, was just replaced. On average, I cook on my egg twice a week. The majority of the cooking is done on grills heated to 350°–400°F, with perhaps 12 lengthy, slow smokes and 12 high temperature (600–700°F) pizza sessions every year.Preparation: I used a razor blade to cut the original seal off, then I scraped both mounting surfaces. I next used rubbing alcohol to wipe both areas until the paper towels stopped looking stained. It took a while to thoroughly clean them both.Install: I began at the base. I roughly unrolled and peeled 2 feet of gasket. Using my left hand to center the gasket on the face and my right hand to hold the roll of gasket, I firmly pushed a 2-3" inch area down before working counterclockwise. I maintained the process until the entire bowl was finished, peeling off another foot or so once roughly half the gasket had been installed. I cut the gasket from the roll, leaving a small overlap of around an inch. The gasket was then precisely matched to the other end by cutting it back. I next went over the lid with the same procedure. The lid was sealed, and I left it alone all day.The gasket is functioning fairly well. Since installation, I have used it for grilling nearly ten times, and the seal always holds. On the occasion when I heated the grill to 700°F to cook pizza, the seal surrounding the interior of the gasket did begin to burn, darken, and slightly stiffen. I'm not sure how many 700F cycles it will last, but it is handling the high heat better than the factory seal. I'll make sure to find out!Note: It hurts to start over with the sticky backing. Although it is factory started, which is good, I would advise peeling the backing past the cut and folding it back when you make your first cut from the roll to avoid having to deal with attempting to get it started again. The top vent and perhaps the bottom vent insert might be redone with what appears to be ample material.
3.9/5
Primary gasket features silicone beading
Made in the USA
Top quality gaskets, seals and O-rings meet or exceed OEM specifications
$234
I made the mistake of buying this gasket thinking it was for a 1999 Sportster. It was entirely my fault for skipping over part of the description. Powersports Superstore immediately switched for the proper gasket. I correctly placed the gasket, for which I also wrote a 5-star review because it was simple to install and of high quality. I valued the quick answer and the numerous additional goods I got from Powersports Superstore. In the future, I'll be conducting business with them.
COPYRIGHT © 2019
