4.9/5
Unlike others' anodized aluminium R134a can tap, ours made of Premium Heavy-Duty Brass to last under extreme conditions. Bult-in O-ring gasket assures leak proof operation. Bonus 3pcs gaskets for replacement in case the O-ring worn out
The Tank Adapter has Schrader check valve in it to prevent blowing back into the supply tank/container and polluting the Environment. The kit includes a cap for double secure and preventing leaking when there is leftover, more secure and reliable
Fits all R-134a cans with ACME threads to directly connect 1/4" SAE (R12 R22) Female fitting AC charging hose (Yellow). Comes with an extra refrigerant Tank Adapter (1/4" SAE flare Female x 1/2" ACME Male) to connect 1/2" ACME (R134a) service hoses (Yellow)
Simple to use, Screw-on design with "T" handle for easy fingertip control to pierce the can and find the "Sweet Spot" (Unscrew approx. 1/4 turn) to allow refrigerant to flow
What you get: 1x R134a Can Tap, 1x 1/4" flare female x 1/2" ACME maleTank Adapter, 1x Cap, 3x O-ring Gasket Seals. At ZoarC, we believe our products that's why we back them 2 years warranty. Any concerns please feel free to contact us, we are here for you
$234
Five stars for price and value, five stars for quality, and five stars for recommendation. Overall rating: 5/5 Product pros include price, quality, and heavy duty Factors to consider include R134 and 1/4" SAE My review: I did not anticipate enjoying this heavy-duty can tap valve as much as I did. The item is made of solid brass and weighs 2 ounces, which is heavier than I anticipated given the pricing. It has a fantastic seal and extra rubber seals are included. When you have this much pressure in your hands, the check valve on it is crucial. It comes with the adapter and is simple to twist on and off. Overall, if you're looking for a 14 valve or r134, I would highly recommend this product.
4.6/5
R134a Charging hose: 19 inch hose with R-134a can to R-12/R-22 service port connection, 1/2 inch end fits R12, 22, 502 fittings; And the gauge has scale readings for R134, R12, and 22. 90-degree push and lock coupler with auto shut off
Sturdy material: made of corrosion-resistant metal that won't wear out or rust over time, a convenient replacement part for you to use; The hose adopted quality rubber material, high pressure resistance and reliable
You will receive: 2 packs BPV-31 bullet piercing tap valve kits; (Each kit including 1 piercing valve, 1 hex key, 2 adapters) and 1 pack R134a charging hoseu00a0with Gauge, 3 packs in total, more convenient for your replace
Easy to use: You only need 1 hex key wrench (included) to install the kit.Its compact design only requires a 2-inch clearance area for installation and use.Warm note:Please note that if you want to attach the gauge with bullet piercing tap valve,you need a retrofit valve,it’s not included
BPV-31 bullet piercing tap valve Replace part No.: AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31. Compatible with: compatible with 1/4 inch, 5/16 inch, 3/8 inch outside diameter pipes
$234
As always, it arrived fast. I read the information before purchasing the R134 adaptor. Once everything was set up and ready to go, I purchased a $10 R134 small can from Home Depot and began the procedure. It was obvious that our Kenmore refrigerator lacked sufficient refrigerant. I carefully released the gas while keeping an eye on the pressure, and bingo. The refrigerator is currently cooling very nicely and no longer issues a high temperature alert. I recommend this DIY tool to everyone.
4.3/5
Sturdy material: made of corrosion-resistant metal, won't wear out or rust over time, a convenient replacement part for you to use; The hose adopts quality rubber material, good pressure resistance and reliable
Package includes: 2 packs BPV-31 bullet piercing tap valve kits (each kit including 1 x piercing valve, 1 x hex key and 2 x adapters) and 1 piece R22 R12 charging hose with gauge, 3 pieces in total
BPV-31 bullet piercing tap valve: replace part No.: AP4502525, BPV31D, GPV14, GPV31, GPV38, GPV56, MPV31, also compatible with 1/4 inch, 5/16 inch, 3/8 inch outside diameter pipes
R22 R12 charging hose: 19 inch in length, only can be applied with home refrigerator adding refrigerant, come with gauge for easily viewing during use, connect to the R-12/ R-22 service port for easy conversion; It fits only those cans with the thread of 1/2 inch
Easy to use: you only need a hex key wrench (included) to install this part; Its compact design only requires 2 inch clearance area for installation and use.This system refrigerant charging pipe with built-in safety valve to prevent accidental venting of refrigerant
$234
Very simple method for refrigerator charging. Clean the suction line with a Brillo pad, clamp the fitting to the line with the needle valve turned counterclockwise, attach the hose, gauge, and can of R134, let the air out of the hose, close the needle valve to pierce the line, then fully open the needle valve to read the suction pressure or vacuum, and then add a small amount of Freon while adding it slowly, checking the pressure as you go. My GE requires a pressure of 2 1/2 pounds on the gauge. Avoid overcharging—more isn't always better! Close the needle valve, remove the hose, and replace the fitting cap once the charge is correct.
3.9/5
Can Be Done Easily With Only A Phillips Screwdriver (Instructions Included)
No Need To Risk The Roof Seal By Replacing The Entire Vent
Replaces Old Ineffecient Fans With New High Velocity Fan
Can Be Retrofitted To Any Existing Vent
Also Works On Non-Power Vents With Some Simple Wiring
$234
I got this fan to replace the subpar one that the manufacturer had put in my recreational vehicle (RV). Installation was simple enough, despite not being as simple as some claim. I spent around 90 minutes on it. There should have been a third hand. Additionally, a replacement screw that would have secured the vent lid lift mechanism to the crank handle gearbox was not offered. The current screw is now overly lengthy. And I believe that I like the classic crank handle better than the twist knob that comes with this fan. As the new installation sits about 1.5 inches lower than the original, I did need to adjust the plastic surround that seals the fan to the ceiling.It runs well after installation. Additionally, some air is moved. plenty of air! Even with the shower curtain drawn, I can feel the air circulating around my feet! When the fan is spinning up, it does make a hum, and when it is moving quickly, it makes an audible roar. Partly from the fan's airflow and partially from the motor's low-pitched hum. The slight hum is preferable to the fan it replaced's high-pitched whine any day. But the fan makes noise.The wire screen takes off, making the fan and screen simple to clean—something not mentioned in other reviews. The screen housing may be removed with just a 10-degree twist.The drastic reduction in light coming through the vent is my greatest gripe. Without the light in the bathroom, you may read with the old, ineffective fan. With this fan, there is currently not enough light, even on a sunny day, to read by without turning on the overhead light.Overall though, I'm happy and would suggest this fan to anyone looking for a replacement bathroom vent fan.
3.9/5
High pressure resistant hose
Built-in safety valve to prevent accidental venting of refrigerant
Extra long 16inch hose, Reading Gauge 0-250psi
Works for R134a/R12/R22, for home/car air-conditioning add refrigerant
Low side gauge monitors pressure to aid in getting a correct charge
$234
Your text will be rewritten by QuillBot. Start by typing or pasting something into this box, then hit the enter key.
3.8/5
Safe for all R-134A systems and recovery equipment
Compatible with all lubricants
Comes with recharge hose
Seals metal leaks in condensers, evaporators, accumulators, receiver and driers
Seals rubber leaks in hoses, O-rings, gaskets
$234
I put off writing this review since I didn't want to ruin the good fortune. Utilized for three weeks and still running strong. Another reason not to write a review is that, although customers should gain from its use, rating things highly on Amazon tends to drive up the price. This item is effective. My AC system leaked after three days, despite the fact that the product material highly advises using it on leaks that last at least two weeks. In my desperation, I discovered leaks on the dryer and evaporator. The compressor shaft seal had a leak, I was also informed. Compressors cost a lot of money, not to mention the installation fees, gas, and oil costs. I spent a minor amount of money to remedy the evaporator and dryer leaks, but the compressor shaft seal leak persisted throughout the system. Unlike other AC seals, this product can be used on metal, which makes it special. I utilized the super seal after determining that the only leak was from the compressor seal. For larger leaks to be successfully repaired, it helps to know the specific location of the leak.
COPYRIGHT © 2019