LED trailer lights are becoming increasingly popular as they offer a number of advantages over traditional incandescent bulbs. LEDs are much more efficient, meaning they require less power to operate and generate less heat. They also last much longer, often 50,000 hours or more, so you won’t have to replace them as often. In addition, LED trailer lights are much brighter, making them easier to see in the dark or in bad weather. And because they’re so efficient, they can often be used with smaller, lighter-weight batteries which can save you money and
Yes, you can replace your incandescent bulbs with LED bulbs. LED bulbs are more energy-efficient and last longer than incandescent bulbs.
Yes, you can replace your trailer lights with LED lights. LED lights are more energy-efficient and have a longer lifespan than incandescent lights. They are also more resistant to shock and vibration, making them ideal for trailers.
Yes, you can mix LED and incandescent lights on a trailer. There are a few things to keep in mind, though. First, LED lights are typically brighter than incandescent lights, so you may want to use fewer LED lights or use them in combination with incandescent lights to get the desired effect. Second, LED lights tend to be more expensive than incandescent lights, so you'll want to factor that into your decision. Ultimately, it's up to you to decide what mix of lights works best for your trailer.
4.5/5
25' split Y-style harness and 4' 4-pole color coded copper wires
Kit includes stop, tail, turn signal lights, two amber clearance lights and wiring harness
Includes 23-foot all-copper wiring harness with UV coated jackets
Trailer light kit for under 80" and Complies with DOT standards
Large 4.5" x 5" lenses and includes license plate light and bracket
$234
I'm very happy with my purchase and the incredibly inexpensive cost. However, keep in mind that we're not discussing a set of American-made lights that are of good quality and durability. I faced two problems.#1: Examine the images. No matter how well-done your installation is, the provided wire terminals will cause corrosion problems. Rain and air humidity, unless you live in the desert, will cause corrosion to form at each light's connection to the harness. The lights could get dim or stop working as a result of this. To avoid spending hours troubleshooting in the future, use butt connections with shrink tubing for a moisture-proof connection.#2 One of the marker lights was discovered to be inoperative after a well-done installation. I thought the issue was with my job, but it turned out that the open was the result of a problem with the bulb holder. unable to be fixed. Be cautious when tightening the mounting screws because some of the plastic is fairly fragile.I'm pleased with the outcomes, especially given the price (which is half of what the well-known Chinese tool supplier charges for the identical thing). On an old tow dolly I was selling, they got me working lights and it looks fine. I might go for something expensive on something I was going to own for a few years.
4.5/5
$234
These came in a 10-pack, which I put on my motorcycle's tour-pak (luggage trunk).I arranged three on each side and four across the back. This significantly increased my visibility, especially at night.Given their brightness, you can clearly see these LED lights during the day as well.That's exactly why I bought this motorcycle—so people could see me better.Due to the rounded sides and back of my tour pack, I selected these shorter LED lights.It would be challenging to put one long, flat LED light appropriately on this type of surface.These shorter ones also performed admirably! I've included a few images. (-:I simply had a little gripe...Each light is installed using two tiny phillips head screws and nuts; the nuts need a 5.5mm socket.I got extra nuts, but they gave me 19 instead of 20 phillips head screws, so I was shorted by one.Because it had different threads, it took me some time to find a little screw and nut that would fit.The one I discovered required a smaller head ground to properly accommodate the light...I put it in my drill to spin it, then used a bench grinder to reduce the size of the head. It worked! (-:These lights are beautifully crafted and come with a great gasket, so even though this was a minor issue, I still gave them five stars.I paid $8.95 for 10 of them, and they have a decent rating and are reasonably priced at less than $1 apiece.
4.4/5
Application: Universal for Trucks, trailers under 80", tractors, semi-trailer, Dump Truck, bus, boat, special vehicle,etc
19 Diodes ( 12 Red+3 Red+4 White ) LED Combination stop turn tail side marker light w/reflector-Street side with license illuminator; Driver Side Serves 7 functions: Stop light, Turn signal light, Tail light, Rear reflex reflector, Side marker light, Side reflex reflector, License plate illuminator;
Package include: 1 Pairs Lights + 2 Gaskets + 4 Screws ã€Tips】 PARTSam is the ONLY authorized seller of Partsam products.If you receive a product that does not arrive branded PARTSam on or not in a PARTSam packaging with logo, please contact that seller for a refund as it is a counterfeit PARTSam product.
Add or upgrade the lights on boat, snowmobile, camper, or utility trailer; High visibility safety lights are EASY TO INSTALL and the wiring details are in the description part; completely sealed and waterproof, its acrylic len are engineered to block water out and ensure the circuits are protected. Super bright LED lights provide maximum visibility and safety. Fully operable in inclement weather, these heavy duty trailer lights are tough and durable for the long term
15 Diodes ( 12 Red+3 Red ) LED Combination stop turn tail side marker light w/reflector-Curb side; Passenger Side Serves 6 functions: Stop light, Turn signal light, Tail light, Rear reflex reflector, Side marker light, Side reflex reflector;
$234
The new lights are much better and last much longer because they are sealed and weather resistant; replace the old blub lights that came with my trailer. They have their own ground wire, so I ran one from my plug to my plug and disconnected the ground from the trailer's body. I made contact with the ground from each light's ground wire, just to be clear. Electrician by trade, I soder all splices and run all wire via conduit, so I don't think I would. ever experienced any issues with these well-built lights!!!2019-03-29 Update I have been using my trailer nonstop for almost three weeks. I noticed that the vehicle behind me seemed to maintain extra space from the tail of my trailer less tailgating at night. I was pulling it empty, so that's when the trailer would do a lot of extra bouncing. The journey had been 100 miles one was and loaded 100 miles back. I think the reason why I've seen this is because the led lights are so much clearer and brighter and because people appear to be paying more attention. So far, we are really happy with these trailer lights. As a third stop light, I'm considering placing one in the middle of my ramp. Since my trailer is an open trailer and can carry 4800 pounds, we had it built to transport a large ditch with cable underground so that when it was loaded, you could see it but it was unlocked. Because I saw a set on a trailer and the person had one as the third stop light, and I was very impressed by how well in bump traffic that third light stuck out so well, I believe it would be a great way to help drivers pay attention. I had to move into the ditch when I looked up at stoplights because the vehicle did not see me. I just thought I'd include it for anyone else having the same issue. due to how clearly the lights are visible during the day. As always, I hope that this prevents an accident or at least helps one person. If so, it was time and effort well spent writing it. Reviews are a huge asset to me in helping me choose products wisely. Therefore, if you're not a reviewer, please attempt to assist others.
4.2/5
Super High visibility and Longer Lifetime LED advantageï¼Complies with DOT standards
Easy to install，The distance of two studs bolts is standard 2†， Direct replacement for your original incandescent bulb unit
Please note, these trailer lights are sealed from PCB, not the housings. You may found there are gaping holes in the housings. As the housings are not sealed, there will be water flows in when use in water, and the gaping holes are made for the water to flow out.
All diodes are LED ,NOT any Bulb !Left Light have 19 diodes : 12 diodes front ,4 diodes on side marker and 3 white diodes facing down for license Plate illumination ,Right Light have 16 diodes : 12 diodes front ,4 diodes on side marker
Left trailer light have 7 function : Stop/Turn/Tail/Rear reflector/side reflector/side marker light/license plate light, Right trailer light have 6 function : Stop/Turn/Tail/Rear reflector/side reflector/side marker light
$234
**Update** On November 18th, I placed a second set of taillight enclosures that I had made for beneath my utility trailer. The passenger rearlight was inoperative. I realized the green wire wasn't working after troubleshooting. Because I was irritated and didn't feel like going through hoops to get my light changed, I was reluctant to call CZC. I reached out to the vendor, and they responded right away. After providing my information, they processed my order the following day and shipped a replacement set right away. A quality product is important to me, but hassle-free customer service is also important. I salute their efforts to find a solution. After reviewing the lights' durability, I'll revise my evaluation.These LED trailer lights are bright and operate flawlessly, and I just installed them. And the wiring colors match those on my utility trailer. When the headlights were on, the first set I attempted in the past didn't function, and the other set's LEDs were not working. I was therefore pleased to observe the effectiveness of the CZC underwater trailer lights. It's comforting to know they will be shielded from the elements even if they will never be submerged in water.
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/71PcTOaV4rL/450/best-trailer-lighting.jpg)
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/91XKLudFVTL/450/best-trailer-lighting.jpg)
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/91EsoN3LsOL/450/best-trailer-lighting.jpg)
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/812RLhX-FyL/450/best-trailer-lighting.jpg)
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/81UD4g0gOrL/450/best-trailer-lighting.jpg)
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/81M1jrYvbmL/450/best-trailer-lighting.jpg)
![15" Red 9-LED Trailer Light Bar with Black Stainless Steel Bracket [DOT Certified] [IP67 Submersible] ID Marker Tail Light for 80" or Wider Trailers](/i/71GpHl1s1jL/450/best-trailer-lighting.jpg)
4.2/5
IP67 SUBMERSIBLE RATED - Waterproof and entirely-submersible for unparalleled all-weather usability; mounting bracket features water drainage notch for added protection.
DOT-CERTIFIED REFLECTIVE LENS - Unlike cheaper, inferior quality ID bars, our unit boasts a DOT FMVSS-108 rated reflective lens design compliant with all relevant laws and regulations.
A MUST FOR 80" OR WIDER TRAILERS - Trailers measuring 80" or wider require identification lights for additional visibility; mount this clearance light bar on the top of your truck/trailer or between the taillights to draw extra visibility to your wide trailer for added on-road safety.
SOLID CONSTRUCTION - Black bracket is made of long-lasting stainless steel, NOT substandard plastic like other light bar brackets. Stainless hardware included.
STRAIGHT-FORWARD INSTALLATION- Mounting bracket features notches on its short sides for easy wire routing; positive input wire and ground wire are attached; mounts on 8.5" centers.
$234
Excellent both above and below the sea!Advice for installers:1. The top and bottom exist! To allow water to drain from between the trailer frame and the light bar, the bottom includes a notch. I notched the "top" and turned it over for mounting because if I had mounted it in that configuration on my trailer, the wires would have exited on the incorrect side.2. In order to prevent the wires from moving around during installation and becoming pinched, I used a hot-melt glue gun to secure them to the frame of the light bar in a few spots. It only needed a few dabs to work. I don't think of that as fixing a flaw; I was just adding a choice.
4.2/5
IP67 SUBMERSIBLE RATED - Waterproof and entirely-submersible for unparalleled all-weather usability; mounting bracket features water drainage notch for added protection.
DOT-CERTIFIED REFLECTIVE LENS - Unlike cheaper, inferior quality ID bars, our unit boasts a DOT FMVSS-108 rated reflective lens design compliant with all relevant laws and regulations.
A MUST FOR 80" OR WIDER TRAILERS - Trailers measuring 80" or wider require identification lights for additional visibility; mount this clearance light bar on the top of your truck/trailer or between the taillights to draw extra visibility to your wide trailer for added on-road safety.
SOLID CONSTRUCTION - Black bracket is made of long-lasting stainless steel, NOT substandard plastic like other light bar brackets. Stainless hardware included.
STRAIGHT-FORWARD INSTALLATION- Mounting bracket features notches on its short sides for easy wire routing; positive input wire and ground wire are attached; mounts on 8.5" centers.
$234
I almost never write reviews because I never actually consider them "honestly." Once I receive my orders, that is it. However, I believed that others would find this useful. We needed to constantly return from fishing early because our previous break light on the boat trailer wasn't working, so I bought these for my husband's boat trailer. So, in the hopes that my husband would enjoy what I chose, I made the decision to buy these, and HE DID. He quickly connected them, noting that each wire has a ground, in contrast to the other wires, and that they are bright. Yellow LED sidelights are also great. It also features a light for the license plate. These are ideal in terms of both value and quality! Worth purchasing. We can now fish at night!
3.8/5
Kit includes stop, tail and turn signal lights, two amber clearance lights and wiring harness
Complies with DOT standards; Side lens are with standard bulb. Corrosion resistant housing. For trailers less than 80 Inch wide
High visibility LED taillights last longer than standard incandescent lights
Includes 23-foot wiring harness with UV coated jackets
Includes 23 and 4 foot 4-pole color coded wiring harness. Product Type: Lighting and Electrical
$234
I purchased these lights to replace the failed incandescent lights on my flatbed trailer. I checked these out with a power supply after receiving them and discovered that the side red lights would go off when the power was turned off (like an incandescent lamp does). Everything inside, save from the red side running light, is an LED, I discovered when I opened it. This light must consume five times as much energy as all of the LEDs put together, and it will wear out considerably more quickly. Although I'll keep this set, I wish they hadn't cut corners.Someone recently informed me that the vendor has changed the description to reflect the fact that the side lens lights are now "standard bulbs." As a result of the description's correction, I'm raising my rating from three to four stars.
3.8/5
Side lens Light and Side marker lights are ALL LED as well ,NOT any incandescent Bulb! Super bright LED quality ,Complies with DOT standards
CLIENT SUPPORT AND SOME NEW ARRIVAL: Please feel free to contact us at first if there is any problem when you receive or use our products. We are always here to support you. In the product description, there are some new arrivals with very good price you may interest
CZC AUTO 12V Submersible LED Trailer Light Kit includes 2 combination stop, tail, turn signal lights, two amber LED marker lights ,25-ft wiring harness,license plate bracket and mounting hardware bag.UPDATE ON 9TH,JUNE,2019.FOR BETTER SERVICE ON OUR CUSTOMER,WE IMPROVED THE WIREHARNESS TO 18GAUGE 100% COPPER WIRE FOR WATERPROOF USE
Waterproof and Submersible Feature and Testing（2nd Image）：We placed light underwater for 3 hour by 3 times each day ,total 5 days,the light worked great underwater! The lights are definitely waterpoof and submersible.Please make sure wires connect correctly and no electronic short before marine/underwater
Application for under 80 Inch width towing vechile,like boat trailer truck snowmobile,etc. Please note, these trailer lights are sealed from PCB, not the housings. You may found there are gaping holes in the housings. As the housings are not sealed, there will be water flows in when use in water, and the gaping holes are made for the water to flow out.
$234
I tow kayaks, a 4-wheeler, a lawn tractor, lumber, and motorcyclists with a 4x8 trailer. I won't assess the lights' water resistance because I don't immerse it when I launch the kayaks. I rewired my trailer today. The entire process took 90 minutes to complete at a steady, unhurried pace from beginning (preparing the materials) to end (putting everything away).I turned the trainer on its side, took out the old lights, and then utilized the old wire to feed the new electrical harness via the conduit affixed to the frame (under the carriage). The metal area where the ground leads for the tail lights would be joined to the frame was then wire-brushed, filed, and sanded. Self-tapping screws were used to ground each lamp to the frame. To aid encourage electrical conductivity, dielectric grease was added to the grounding surface after it had been cleaned and sanded.I admit that the ground's crimp-on termination (near the tongue's tip) was a bit light, but I still utilized it. It works. In order to avoid relying on the crimps to pierce the insulation for contact, I did clip a little portion of the insulation away and crimp it straight to the bare wire rather than to the insulation. I felt secure utilizing the offered terminal because there is no strain exerted on this connection. Again, for that grounding connection, metal was cleaned, dielectric grease was applied, and self-tapping screws were employed.My car is an F150. The flat-4 connector fitted on the car is female. It wasn't until I removed the "boot" of that connection and revealed three male connectors that the provided wiring harness connector fit it. The exterior dimensions of the fourth connector (green wire) were meticulously shaved down until they snugly fit into the shaped receptacle fitted to the vehicle. By slightly spreading out each pin with the blade of a pocket knife, the three male connectors were then expanded in diameter to provide a stable connection. This was made simple by each connection having a slot that was already there. To prevent snagging the wires, the lights were soldered to the harness before being wrapped in electrical tape and zip-tied out of the way. To prevent ants and spiders from building nests inside, plastic ribbed sheathing (from the old wiring) was put to the new wiring harness where it emerges from the tongue and taped closed on both ends.Both the female flat-4 connection on the car and the male flat-4 connector pins on the trailer were greased with dielectric grease. The wiring harness was connected in, the lights were checked, and the trailer was fastened to the hitch. A vast improvement over the incandescent lights they replaced, all the lights worked flawlessly and were quite bright.If I decide to submerge the trailer for boat launching, I'll use silicone caulk to waterproof the lenses and housing. I'll unplug the harness from the car as a precaution. However, kayaks can be launched without a trailer and are simple to carry to the water's edge.All in all, I'm extremely pleased with my purchase and the way this replacement kit works. The trailer and lights must now be used, and their durability must be tested. If the events of today are any guide, I think my optimism will hold.Update suggestion: Switch out the flimsy terminal ring for one that is more durable. Want to sweeten your goods really bad? a tiny packet of electrical grease should be included.
3.6/5
DOT certified
Features two 4-1/2" diameter red brake light on one side and amber flasher on the other side
Heavy duty magnetic base with 11-lb pull keep lights stay in place
Includes 20-ft color coded wiring harness with standard 4-flat wire vehicle trailer connector
Ideal for all towing applications under 80" wide
$234
exactly what was promised! The magnets appear powerful enough to remain on the automobile, and they actually did. A trouble-free cross-country trip from Albuquerque to Fairfax, Virginia. They remained exactly where I had put them!The wires' lack of protection bothered me, but considering the cost, I can't really gripe. I did cover the wires in two rolls of black electrical tape to keep them safe. Overall, extremely happy!
3.4/5
Kit includes 2 combination Submersible running/stop/tail/turn signal lights,license plate bracket and Mounting Hardware， 25ft length of 4 pin wire Harness for enough use.UPDATE ON 9TH,JUNE,2019.FOR BETTER SERVICE ON OUR CUSTOMER,WE IMPROVED THE WIREHARNESS TO 18GAUGE 100% COPPER WIRE FOR WATERPROOF USE
CLIENT SUPPORT: Please feel free to contact us at first if there is any problem when you receive or use our products. We are always here to support you.
Each rectangular light size：8" Length* 3" width* 2-3/4" height,Stainless steel hardware for under and over80" marine towing vechiles
Left light have 22 diodes which include 4 diodes for lincense plate light function,Right light have 18 diode. Super bright LED quality ,Complies with DOT standards
Waterproof and Submersible Feature and Testing（2nd Image）：We placed light underwater for 3 hour by 3 times each day ,total 5 days,the light worked great underwater! The lights are definitely waterpoof and submersible.Please make sure wires connect correctly and no electronic short before marine/underwater
$234
To increase my visibility, improve my ability to communicate with other drivers about my intentions, and to be in accordance with local rules, I added this to my motorcycle carrier. Additionally, when connected properly, it simply looks amazing. This kit contains the lights on the bottom. They are big, bright, and completely factory-like. a need if you travel on roads. safer to be safe than sorry. Additionally, they have a license plate mount, which I didn't photograph for obvious reasons. The plate can be mounted anywhere, including underneath the lights. The plate is lit by one of the lights at night.
There is no requirement in the U.S. for reflective tape on trailers, but it is a good idea to have it. The tape will make your trailer more visible to other drivers, especially at night. It is important to be as visible as possible when you are on the road.
LED trailer lights do not require a resistor. LEDs are more efficient than incandescent bulbs and last much longer.
LED trailer lights are much brighter than traditional incandescent bulbs, and they use much less power. LED trailer lights do not require special wiring; however, if your trailer is not equipped with LED-compatible wiring, you will need to install a LED-compatible wiring harness.
Most trailers have some sort of lighting on the side. This is so that other drivers can see the trailer, and so that the driver can see the side of the trailer. If you are driving a trailer without any lights, you may be risking an accident.
A 7-pin trailer plug does not charge a battery. The 7-pin plug is designed for use with trailers that have electric brakes. The 7-pin plug is also used to provide power to accessories on the trailer, such as lights.
The lights on the back of a trailer are called tail lights. They are required by law in many states, and are used to help other drivers see the trailer at night. Tail lights are usually red, but may also be amber or white.
COPYRIGHT © 2019
