Most car door edge guards are made of clear vinyl and attach with double-sided adhesive tape. They're designed to protect your car's door edges from nicks, scrapes and dings when you open your door in tight spaces. Some people swear by them, while others find them to be a waste of money. I fall somewhere in the middle. I think they're a good idea in theory, but in practice, they're not always worth it. The main problem is that the adhesive tape doesn't always stick well, especially in hot weather. The guards
Most homeowners think door protectors are worth it because they help keep their homes looking nice and new. They also help keep out dirt, dust, and other debris that can damage the door.
Most door edge guards can be removed without too much difficulty. However, there are a few things you need to keep in mind. First, make sure you have the right tools. A flathead screwdriver or a putty knife should do the trick. Second, be careful not to damage the paint on your car door. Third, take your time and be patient. It may take a few tries to get the guard off without breaking it.
There's not much you can do about door dings once they've happened. You can try to park in a spot where there are fewer cars, or park away from other cars. You can also try to park in a garage.
I've bought door edge guards from neighborhood auto parts shops, but I wasn't very impressed with their quality. The "chrome" would peel after many months in the scorching Florida summer, the guard's ends would readily separate, and the adhesive would become soiled and ooze. I went to Amazon out of frustration because there were so many options there. After perusing a number of reviews, I made the decision to buy this item. When it finally did, I realized its superior design. The guard has an EPDM rubber coating that is pretty thick, but the REALLY amazing feature is within. Throughout the roll, there are tiny quarter-inch chunks of segmented U-shaped metal (see picture). No glue is required because the metal parts hold the edges of the door. The roll itself is substantial and flexible. I had PLENTY extra length for all four of my SUV's doors, which allowed me to redo one of them after making a mistake. Regarding the straightforward installation, I took a chance and, despite the guidelines' advice to use a mallet, I used a small ball-peen hammer. I then tapped VERY CAREFULLY to avoid chipping the paint underneath (DO NOT USE A HAMMER UNLESS YOU ARE WILLING TO ACCEPT RESPONSIBILITY FOR THE OUTCOME). Following installation, I used needle-nose pliers to remove any superfluous metal pieces, and I carefully applied ATV Black Gasket Maker to the extreme ends of the cuts to ensure that the holes were entirely filled. Voila! My doors have a polished and contemporary appearance at once. My coworkers have heard about this product from me, and they appear eager to test it out as well. The Strongman Tools Door Edge Guards are superior to all other guards I've used, in my opinion. Just in case you were curious, I DID NOT RECEIVE THIS PRODUCT FOR FREE AND THIS IS MY HONEST OPINION.
It's safe to say that these guards kept me from innumerable scratches and damage. **EDIT** Nearly 1.5 years later, they're still rock strong and look amazing. A My 2018 Jeep Wrangler had only been in my possession for 24 hours when I noticed a little scratch forming on the door jam, which was painted the same color as the car. It's typical to step on that area when you enter, allowing any rocks or other objects on your shoes to damage the paint there.These entry guard kits fitted perfectly, took little time to install, looked factory-original, and blended in well with the panel and body color. Pro-Tip: Before installing, place these in front of a heater or put them in the sun for a couple of hours so they warm up and become more flexible. This will aid the 3M adhesive strips in forming a solid contact bond. Make sure you know exactly where the installation should begin by performing a dry fit before attempting to draw the red film over the 3M adhesive strips to ensure that they are aligned. To ensure that the mounting glue sticks down firmly, clean the surface with a lint-free cloth or alcohol wipe.
â–·100% Risk-Free Warrantyâ–·: One Year Warranty. Contact seller directly if any issues, MATCC Service Team will respond you within 24 hours during working days.
â–·Advantages: Waterproof, isolator noise, corrosion resistance, high temperature resistance, wear resistance, anti-aging, UV resistance. Easy to install: Direct replacement. Just push on the rubber seal above the install place.Attention to truck/van owners, please ensure your door edge thickness prior to purchase.
â–·The install place1: In the metal edge of the car body between the car door and car body. In the external edge of the car door and more.
â–·The install place2: Also can be use in the window above the car. Window panel minibus. Border heavy equipment. Covering the edge of the sharp metal. Vinyl window decoration boat.
â–·Fitment: Edge thickness: 2mm( 0.08"). Product specifications as shown in figure. These door edge guards will protect your vehicle from nicks, chips & scratches, for most universal car. Please check the size and your car door before order, connect seller is any displeasure.
Since Wrangler doors swing freely and lack a mechanism to control how quickly they open and close, I bought this to preserve the edges of my doors. I chose this brand without doing any research; I'm glad I did. The midsection of the guards' flexible metal can conform to the edge of the doors. The rubbery material has a wonderful texture. Another roll that I purchased for a pittance from an auto body shop turned out to be nothing more than rubber with a small amount of sticky adhesive within (no flexible metal). We'll get a roll or two more of this for our other car!Notably, finishing both of my doors took roughly 30 minutes. Use a rubber mallet or other tool to firmly and evenly install the guards all the way around. Since the gap on the guards was a little too small in some places for me to even reach on my doors, I also used a flat-edged screwdriver to push apart the opening. Definitely worth the time and work!
Advantages: Waterproof, isolator noise, corrosion resistance, high temperature resistance, wear resistance, anti-aging, UV resistance.
The install place1: In the metal edge of the car body between the car door and car body. In the external edge of the car door and more.
The install place2: Also can be use in the window above the car. Window panel minibus. Border heavy equipment. Covering the edge of the sharp metal. Vinyl window decoration boat.
Fitment: 32Ft(10M) long. Edge thickness: 2mm( 0.78"). Product specifications as shown in figure. These door edge guards will protect your vehicle from nicks, chips & scratches, for most universal car.
Easy to install: Direct replacement. Just push on the rubber seal above the install place.Attention to truck/van owners, please ensure your door edge thickness prior to purchase.
First of all, I'm a girl, and I installed this quite quickly. My Mazda CX9 SUV has enough room for 4 doors, a hatch door, and a good 10 feet extra, so you could install a front hood if you so desired.Although there is no glue or adhesive used, internal metal clamps within the rubber allow the trim to be applied quite tightly. The fabric is tightly fastened! It effortlessly navigated the curves in my door and remained stuck. It's simple to cut.I appreciate how shiny and textured the finish is. It enhances the appearance of your automobile and protects the ends of your doors from nicks. I should have purchased this merchandise years ago.very flexible On a steamy morning, I put it in on my driveway. It should be applied slowly, inch by inch. Simply continue to press it in until it is completely flat against your doors. Avoid rushing this procedure. I completed the four doors and the back hatch in just under 30 minutes.Black or chrome? I couldn't decide. I chose black because my pinstriping and other components were black. I would definitely suggest this to anyone!
âœ”ã€MATCC COMMITMENTã€‘:MATCC provides 100% satisfaction warranty, feel free to contact.
âœ”ã€CAR DOOR EDGE GUARD SPECIFICATIONã€‘:2mm( 0.78"") thickness. 32Ft/13Ft Door seal strip will prevent nicks, chips & scratches, for most universal car.
âœ”ã€EASY TO INSTALLã€‘: Direct replacement. Just push on the rubber seal above the install place.Attention to truck/van owners, please ensure your door edge thickness prior to purchase.
âœ”ã€INSTALLATION POSITIONã€‘:1.In The Metal Edge Of The Car Body Between The Car Door And Car Body. In The External Edge Of The Car Door And More.2. Also Can Be Use In The Window Above The Car. Window Panel Minibus. Border Heavy Equipment. Covering The Edge Of The Sharp Metal. Vinyl Window Decoration Boat.
âœ”ã€ADVANTAGESã€‘:Built-in metal clips and gripping tongue help to fixed, Anti-impact, waterproof, isolator noise, corrosion resistance, high temperature resistance, wear resistance, anti-aging, UV resistance.
To install this item, avoid using a hammer or mallet. I did that, and while the edge guard did, of course, seat entirely, I later saw that there were certain areas where the guard's edge was not sealing, not sitting taut and flat against the car door, leaving small holes that would enable the passage of water, debris, etc. under the edge guard's lip. The metal clips inside the edge guard are deformed and forced to spread when this material is hammered, which prevents the edge guard from properly sealing. Installing this stuff correctly simply requires the use of one's thumbs and palms. Fortunately, I had enough material to repair what I had hacked at with a 2x4 and a rubber mallet.
âœ…MULTI FUNCTIONS CAR DOOR ACCESSORIES. WINUNITE car door edge guard prevents door scratches(when open the door), chipping paint and rust and improve noise reduction.
âœ…32Ft CAR DOOR EDGE GUARD. WINUNITE car door edge guard will protect your vehicle from nicks, chips, scratches. 6mm(about 1/4') thickness U channel design, fit easily over any door edge. NOTE: The end clips exposed at both sides need to be pulled out with scissors.
âœ…METAL CLIPS , NO DROP OFF. WINUNITE car door edge guard trim with individual internal metal clips, completely tightly fit, no drop off.
âœ…UNIVERSAL FIT(NOT suitable for Tesla). EASY INSTALLATION. WINUNITE car door edge guard could be used on engine door, tailgate door, front and back door. NOT suitable for Tesla vehicles. VW Passat, 2015 Chevy Tahoe, 2019 BMW X3 M40i, 2013 Mercedes C250.
âœ…LIFETIME WARRANTY. WINUNITE provide lifetime warranty for this product, if you have any question in using product, please feel free to contact with us.
Easy to install, I advise using a blunt tool to actually get the trim as close to the door as you can, ensuring a snug fit (so the doors close), before cutting it with scissors or a utility knife. It appears to be made of metal, but closer inspection reveals tiny scores where the metal has been divided into pieces for the trim. I finished the back and all four doors, and I still had enough for another car. looks normal and doesn't protrude or flare out from the car. Perfectly functional doors that tolerate the weather
1ï¼šFlexible and durable quality materials. The metal edge between the door and the body. On the outer edge of the door and more. The tape is designed for the inner edge of the door so there is no residue on the outside.
5ï¼šIt fits most of the car. Pay attention to the truck/truck owner, please ensure the thickness of your door edge before purchasing.
2ï¼šProtect your car for years of durability or high gloss, good durability, abrasion resistance, cost effectiveness, no fading, flaking, falling off or damaging your paint finish.
4ï¼šThe benefits of installing anti-collision strips, restore high-quality driving environment, anti-collision and cushioning, prevent paint friction, dust and water proof, clean and clean inside the car, improve sealing, better sound insulation and noise reduction.
3ï¼šBrand new glossy/look look/improve vehicle feel/effectively prevent bumps, these door edge guards will protect your vehicle from nicks, chips and scratches. They are easy to install and have no tools. They are U-shaped and easy to install on any door edge.
On three different automobiles, I installed door edge protectors. Due to its extreme flexibility, this one is by far the best. This means that it is simple to maneuver around the door's curvature because it bends so easily. When you go around curves, the others do not stay and keep pushing it back in. This door edge guard also has 3M tape attached behind it to keep it in place. The others won't hold up in hot climates like Florida as they only have glue inside and no 3M tape. Eventually, the glue begins to peel off.
Fits all Tesla Model 3
Easy installation in under 5 minutes
Self-healing technology allows minor scratches to automatically disappear
Made with Premium 3M Scotchgard Pro Material
I held off on publishing my evaluation for about a month since I wanted to ensure that it continued to function over time. I am really happy with the outcome. On the model 3 door sill, the aluminum portion is prone to scratches and dust buildup. If you do not clean carefully, the dirt may harm the sill and result in damage that is difficult to repair. This transparent shield does a terrific job. Cleaning is quite simple, the dirt does not accumulate as much, and it looks nice and glossy. I am also less self-conscious while getting in and out of the car because I am no longer concerned with damaging the sill. You won't even notice it is there because it is cut nicely. Cleaning the door sill, applying the included soap solution, placing the film on the sill and adjusting the boundary, squeegeeing out any air bubbles, and you're done with installation in less than a minute! Because it can slide, don't forget to gently remove the air bubbles and press and hold on to the end. All model 3 owners should buy this product, in my opinion.
Car Door Edge Guards: 3 colors (White, Black & Red) to select to match your vehicle color, almost invincible after installation.
Easy to Install: Direct replacement. Just push on the rubber seal above the install place.Attention to truck/van owners, please ensure your door edge thickness prior to purchase.
Clear vinyl door guards:Thin/Slim design yet it efficiently protects your door. "ATTENTION! - NOT SUITABLE FOR DOOR THICKNESS MORE THAN 2mm ( .078 INCH)". ADHESIVE: Built-in strong double-sided adhesive tape and does not melt under hot weather, no glue needed. The adhesive tape is designed to paste on the inside door edge, therefore it will not leave any residue on the outside door after the door trim is removed.
Advantages: Waterproof, sound insulation, corrosion resistance, high temperature resistance, wear resistance, anti-aging, UV resistance.
Clear door trim guard: (No Glue Required)High quality TPO rubber material, heat resistance, abrasion resistance, anti-aging, waterproof & UV resistance.
I recently purchased a new vehicle and wanted to increase the door edges' level of safety (heavier doors than my old car). Although I generally open my car door carefully, this provides a bit additional cushioning.Cutting the piece to length and removing the small red plastic covering the adhesive material made installation incredibly simple. I'm happy I took the time to read a few of the reviews. There aren't any guidelines. Place the door's interior with the adhesive side down.
To avoid door dings, park your car in a garage or carport whenever possible. When parking in a public space, try to park next to larger vehicles that will block access to your car doors. When driving, be aware of your surroundings and give yourself plenty of space to open your doors. You can also purchase door edge guards or install clear vinyl film on your car doors to help protect them from dings.
To protect the inside of your car door from scratches, you can use a variety of methods. You can line the door with a soft material, such as felt or foam. You can also apply a clear protective film to the door panel.
There are a few ways to add extra protection to a front door. One way is to add a security system that will alert you if someone tries to break in. Another way is to add a deadbolt lock to the door.
Reattaching rubber trim on a car door is a relatively easy process. First, clean the area where the trim will be attached with rubbing alcohol. Next, use a small amount of super glue or another adhesive to attach the trim to the door. Once the trim is in place, hold it down for a few seconds to allow the adhesive to set.
Most door edge guards cost between $5 and $10 per linear foot, with installation costing between $50 and $100 per door.
Most car door guards are made of metal or hard plastic and are designed to protect your car doors from dings, dents, and scratches. While some people think that car door guards are unnecessary, they can actually be very helpful in keeping your car doors looking new. If you live in an area with a lot of trees or other objects that could potentially damage your car doors, car door guards can help to prevent this damage.
COPYRIGHT © 2019