Best Sink & Bathtub Faucet Spouts in 2022

Last update: December 29, 2022

Are tub spouts standard size?

Most tub spouts are standard size, but there are some that are not. You will need to measure your tub spout to be sure.

Can you just replace the tub spout?

If your tub spout is leaking or damaged, you may be able to replace it without replacing the entire valve. To do this, you will need to identify the type of valve you have so you can purchase the correct replacement spout. You will also need to turn off the water supply to the valve before you begin.

Do all tub spouts unscrew?

Most tub spouts are designed to unscrew from the pipe that leads to the showerhead. However, over time the spout may become difficult to remove. If the spout is difficult to remove, you may need to use a wrench to loosen it.

Do plumbers replace bathtub faucets?

Plumbers are trained to replace bathtub faucets, and they have the necessary tools to do so. However, depending on the type of faucet and the severity of the damage, it may be more cost-effective to replace the entire faucet.


MOEN 106479 Temperature limit stop kit, Posi-Temp 1 handle tub/shower, Small, Unfinished Review:


Exact fit and worked as intended. We have very hard water, and the old valve, which was 7 years old, wouldn't work because of water deposits, leaving us with just cold water and no hot water. The old valve was challenging to remove, but thanks to earlier reviews, I was able to easily do so after buying the Moen 104421 Cartridge Puller for 1200, 1222, and 1225 Single Handle Cartridges. Make sure to flush the system to get rid of silt after removing the old valve.



DANCO Decorative Metal Tub Spout Remodeling Cover Ring, Chrome, 1-1/2-Inch ID and 3-5/8-Inch OD (10007) Review:


The exact issue I experienced in our kids' restroom was solved by this Danco spout ring. The gap between the tile wall and the spout, which was our problem, was about 1/4 inch. If it hadn't been closed, water might have accumulated behind the wall. I had no choice but to either cut the copper pipe by around 1/4 inch or install this spacer since I could not ignore the problem and the diverter spout could not be tightened any further. Because I did not want to run the chance of the spout not threading properly after I hacksawed it, I decided to add this spacer.Anyway, the diverter spout was then tightened straight up around the ring, creating a nice-looking, water-tight seating for the spout, which fit on right over the copper pipe thanks to some flexible foam. The actual ring is made of a thin, polished metal.This proved to be a fantastic, low-cost remedy for the potentially costly (water damage) or harmful (black mold) effects of water getting behind our bathroom tile wall. For reference, I've included a few images below.



Moen 3801 Tub Spout with Diverter, 1/2-Inch Slip-fit CC Connection, Chrome Review:


I went to the hardware store and purchased a Danco at a bargain after my diverter jammed for the second time. Slip fit, simple installation, no issues. But even though I'm an engineer, I cannot for the life of me understand what that set screw accomplishes. As it turned out, the slip fit deteriorated after just a year and kept blasting off in the middle of showers. No fun.Do an Amazon search to find a nice one. I discovered the other well-known Moen, but the reviews claimed that plastic was used in place of metal. For me, no. However, this one, which was metal for not much more money, received the same fantastic evaluations, particularly the bit about the screw clamp. I promise it's worthwhile. Purchase one-day delivery and schedule your substitute showering for the following day or so.Just the correct size hex key wrench is needed; installation was straightforward. Your results may vary, however I found that the spout needs a little silicone caulk around it because the way my copper pipe was adjusted left it with a small gap.The system runs incredibly well, and mine even switches back when the water is shut off.I'll let you know if anything alters!



American Standard 8888026.002 Bath Slip-On Diverter Tub Spout, 4 inches, Polished Chrome Review:


The interior design appears to be identical to that of the Danco universal tub spout, however it appears that AS bonded the plastic ring to the internal plastic nipple, eliminating the need to mess with it during installation. It appears that silicone grease was pre-applied to the O-ring inside. It installs quite easy, and all that's left to do is use a 4mm allen/hex wrench to tighten the set screw. There are no installation guidelines provided.To avoid harming the O-ring, they've placed a label over the opening where the copper pipe enters to remind you to deburr the pipe before installing. The tube length that protrudes from the wall must fall between a range of 1-1/2 to 2-7/8 inches, according to the sticker.Even when in the shower setting, it continues to drip once or twice every few seconds. However, it is far preferable to the constant trickle of water on the danco.



Delta Faucet RP5833 Tub Spout for Non-Diverter, Chrome Review:


The only reason it doesn't get five stars is because all the information regarding it is inaccurate. I'm writing this in order to assist others.The precise dimensions of the Delta RP5833 Tub Spout are listed below.False information on Amazon is: 5/8 to 1-5/8 inches from the wall's surface, thread onto a 1/2-inch IPS nipple.False information on the package is: Install 3-7/16 to 3-9/16 away from the wall surface on a 1/2 threaded pipe nipple.The spout's snout is where the threads are located.This DOES fit where the pipe nipple end is between 3-13/16 and 3-15/16 inches from the wall.Actual measurement is 3-5/8 from the spout's end to the start of the threads.Since pipe threads are tapered, you probably won't be able to screw this on more than 3–4 turns without filing down the threads of the nipple. The actual distance between the end of the spout and the end of the threads is 4–1/4. The spout will inch closer to the wall with each full turn it receives on the threads.The spout's overall length is 5 1/4.My 25-year-old, rotted-out spout was replaced. I made sure there was no fixed screw on the base, which would have indicated a slip-on spout. I then used a probe to check if there was a 1/2 inch copper pipe in the middle of a hollow spout in one of the rotted-out holes. Using a huge set of pliers at the spout's end, I attempted to detach the old spout. I tried applying moderate pressure, but it wouldn't budge, and I was reluctant to use too much pressure for fear of breaking the pipe. The previous spout was chopped off using the cutoff wheel on my Dremel tool. It cut effortlessly. I made two cuts around it before slicing the removed circles in half lengthwise. The spout's nose was still attached after that. I once more chopped some relief threads off the end of the pipe nipple threads with the Dremel. After a few cuts, I was able to grasp the pipe with one set of pliers and twist the nose with another set, and it came out. This causes some heat and expansion in the nose. Once more, I didn't use undue force. Unless you want to switch to a slip-on spout, which would be a simpler choice, avoid damaging the pipe nipple threads.My pipe's nipple protruded from the wall by 4-1/16 inches. When fastened on tightly, the Home Depot Danco screw-on replacement for me fell 1/4 inch short of the wall because it was only 3-1/2 inches deep to the start of the threads in the snout. This Delta RP5833 was 3-5/8 inches deep to the start of the threads, however it would only screw on three turns before falling short by an eighth of an inch. The spout regularly became stuck when I was testing the fit, so I used a strap wrench to pry it free without damaging it.A fresh nipple would lose half an inch after I cut it off and sweated on it, making it too short. Although I had the option, I saved unsweating the old nipple until last.I had the option to remove the nipple and change to a "slip-on" fitting. The simplest choice would have been this. For a good seal, I would have had to remove the corrosion and gunk from the pipe.To get 5 turns of the spout and a tight fit against the wall, I decided to file down the threads on my tapered pipe nipples. With each turn, the wall gets 1/16 inch closer. I started my tapered threads at.809-..832. I began by using a flat file to remove a small amount of the OD, followed by a micro file to further cut the threads. I continued in this manner until it was tightly fastened to the wall after five rotations. The OD of the nipple threads was reduced by about.020 (.790 - .810). In order to avoid future galling, I applied pipe dope to the threads.Sorry for the lengthy post, but if I had known all of this before I started, I would have simply removed the nipple, used a slip-on spout from Home Depot, and finished the project much more quickly.



Symmons TA-10 Temptrol Flow Control Spindle Review:


This Symmons TA-10 spindle was a perfect match for the Temp-Trol valve in our upstairs tub and shower. At the same time that I changed this component, I also replaced the heated and cold chairs. Although a little pricey, this spindle is an authentic Symmons OEM component and functions flawlessly. I'm hoping it will survive as long as the previous one did, which was roughly 12-years with almost daily use.



Danco, Inc. 80765 Universal Tub Spout, Metal, Chrome, Review:


lovely, sturdy spout Due to (apparently) years of hard water buildup, my old one stopped operating, and we were unable to get the water to switch or redirect to the showerhead. This one's installation seems simple enough. But no matter how hard I tried or how many times I tried (and how many times I rewrapped the pipe in plumber's tape), I was unable to thread the adaptor onto the pipe far enough. In the end, we really installed the apartment as a whole unit by screwing it back into the spout. We could only get it flush with the spout ring after that. But it works really well! Water is smoothly diverted to the showerhead with only a small amount of pressure drip coming from the spout.



LASCO 08-1061 Four in One Bathtub Spout Adapter Slip Fit for Copper Review:


I bought a Pfister bathtub faucet set from Lowe's. My old pipe was not threaded and was too short to direct thread, and the ridiculously costly kit did not include an adaptor set for the tub faucet.However, this adapter set performs flawlessly in its place. The end of the sleeve that sits between the pipe mount and the faucet mount had to be milled off because it was too long and was in touch with the inside of the faucet, preventing the faucet from sitting flush against the shower wall. It fit perfectly after being cut to the sleeve's suggested line.With the interior treading as long as it is and the indicator markings, it was inferred that this would be a problem or that it was okay to do, so the directions only received 4 stars.



EZ-FLO 15087 Bath Tub Diverter Spout with Side Outlet, Chrome Finish Review:


Despite my skepticism, I bought this product despite how inexpensive it was. It took only a minute to install, and thus far I haven't had any issues. It's a fantastic and affordable alternative to a bath without a shower. This may be used to create an immediate shower for less than $50 if combined with a hose, shower head, and mounting bracket.



DANCO Universal Tub Spout without Diverter, Brushed Nickel, 1-Pack (89247) Review:


This product is appropriate for a 1/2" copper pipe stub out that is 2.5–3 inches in length. Before making my order, I phoned Danco's customer care representative to confirm. Because I had the right tools (sandpaper, silicone oil, a screwdriver, and teflon tape), patience, and being a handy housewife, I found the Installation to be fairly simple. After installation, make careful to check for leaks (for example, run the shower and look to see whether water drops out along the wall). The "O"-ring didn't sit perfectly flush on the adapter's lip on my first three attempts. I took my time, disassembled everything, and went through the installation process until I got it right on the fourth try. The business has a YouTube video to show how simple the installation was. So far, all positive!


How do I know which tub spout to buy?

How do you measure a spout?

A spout is measured by its length and width. The length is measured from the top of the spout to the bottom, and the width is measured from the furthest point of the spout to the nearest point.

How long is a standard tub spout?

The standard tub spout is about 6 inches long. This can vary depending on the manufacturer, but most tub spouts are around this length. This is the perfect size for most bathtubs and provides good water pressure.

How much does a plumber charge to install a bathtub faucet?

Assuming you need a plumber to install a bathtub faucet, it would generally cost between $45 and $200 per hour. However, the total cost will depend on the complexity of the job and the experience of the plumber.

How much does a plumber charge to replace a bathroom sink faucet?

How much is it to replace a bathtub spout?

If your bathtub spout is starting to show its age, you may be wondering how much it will cost to replace it. While the cost will vary depending on the type of spout you choose and the plumber you hire, you can expect to pay anywhere from $100 to $200 for a new bathtub spout.