4.8/5
2.4g receiver antenna with IPEX 4 Generation connector
A must have for Frsky XM+ and X4R rx/tx field repair
Precision machining,Low loss signal stability,High sensitivity, High quality
5.9 inch (150mm) - Length, RF113 Silver plated Wire Material
Smaller ipex connector type fit for new FRSKY X4R-SB frsky xm mini receivers
$234
a great value. the R-XSR AND the XM The overall length is 150mm, and the active antenna is 33mm, as can be seen in the photographs. And if you enlarge the receiver image, the printing on the device makes it obvious that it is an R-XSR. The stock antennae that came with the R-XSR are the two smaller ones. My RSSI is significantly stronger since I converted from the stock antenna to this size (longer active element, 33mm) a few months ago, and my OSD and GPS also indicate that the flight distance has risen. I'm currently flying at a quarter-mile or more with a 65-70 RSSI. With the stock antennae's reduced size, I was unable to do that.
4.6/5
5.8 GHz Circular Polarized Antenna Set for transmitter and receiver
Material: Cu, Weight: 12g
Gain: 3DBi,Frequency range: 5600-5950 MHz
Connector: RPSMA
Omnidirectional: 3dB horizontal lobe width: 360°,3dB verticle lobe width: 120°
$234
I'm using an HGLRC F4 V5Pro along with this antenna. Together, they function really well. The product was as advertised and very nicely crafted, and shipping was completed very quickly. Although I didn't fly far, it is incredibly effective at close quarters. Short range refers to a distance of no more than 200 feet from my position. Soon after the package arrived, the vendor got in touch with me to check on how I was feeling. They surprised us by doing this, which was a very kind gesture. Makerfire 2 pieces of 5.8GHz FPV antenna with circular polarization for FPV racing drones like the QAV250, etc.
4.3/5
[Imported PC+ABS Material]: FOXEER RHCP antenna for 5.8GHz FPV racing,can withstand high strength impact,support you better range and performance in any orientation
[Longer Transmission Range]:Exquisive workmanship, manufactured and tested to highest standards.Best in class range and signal quality
[Mini size & light weight]:22.7mm height/ 17.4mm Diameter,4.8g / pc
[Updated Version]: 5.8GHz center frequency and 500MHz (5.5 - 6.0 GHz) bandwidth range, FOXEER FPV Antenn have exquisite workmanship, best in class range and signal quality
[IRoot reinfircement design]:FOXEER lollipop antenna can be bent at any angle maintain,360°protection low feeder loss, easy to install
$234
Because they are not in contact with the ground during crashes and severe landings, these have excellent durability. My own has a 90-degree fitment so that it can stand up and be safe. Compared to the signal I was receiving with the default FatShark antenna that came with my drone, I find the signal on these to be stronger. I fly my drone all around my house, and when it is on the other side of the house from me, I need a strong signal. I have never had better reception than I do with this antenna. While the drone's antenna provided excellent reception, the FatShark goggle antenna's performance lagged behind. I tried placing these on the drone and the goggles, but the signal was weaker when they were on the goggles. They probably require a stem so that they are raised above my head and can do their job. To check if an antenna extender will help, I might try to purchase one. However, I believe that having this on the drone plus the longer FatShark antenna on my goggles is a terrific combination. I would advise doing this.
4.2/5
Use Traxxas stock and hop-up replacement parts to get the most out of you Traxxas RTR vehicles!
For use with all Traxxas AM transmitters
Telescoping antenna
This is replacement hardware for use on Traxxas vehicles, consult your user's manual for exact parts listings.
This product is made from high quality materials, and designed for lasting performance.
Replaces worn or damaged parts
$234
It functions well and looks good. I wish the description had mentioned the antenna's base diameter. I had to carefully hand drill the case out so that this antenna would fit because it was too big for the housing I was replacing a lost antenna from. For those who need to know, the antenna's dimensions are 6.75 inches when collapsed and 37.75 inches when fully extended. The top tip is larger at 10mm and is slightly over.25 inches in diameter (6.86mm) at the base. Once the casing was drilled out to fit, the threaded bottom, which seems to be a brass insert a bit smaller than 6-32 (It is probably metric), screws on to the top of my base station scanner without any issues.
4.1/5
Include: 1 xRemote signal expansion board ; Note:In addition to the above these things, and no other things.
Features: Remote signal expansion board, aluminum material, which is an idealized radar antenna and produces a pencil beam. If the reflector has an oval shape, it generates a fan beam. To avoid signal problems due to the loss or fried machine situation.
Compatible with DJI Mavic pro / Mavic Pro Platinum / Mavic 2 Pro / Mavic 2 Zoom / Mavic Air / Spark
This kinds of Signal booster significantly improves the transmitter and Wi-Fi video connection performance in the open area and make the signal more stable.This don't fit DJI Smart Controller!!!
Signal enhancement, flight more security. The film of the surface is torn off prior to installation, with the metal sheet facing outward
$234
To increase the range of my DJI Spark, this is a fantastic small addition. I obtained more than 50% more mileage with my Spark using the signal booster than without, flying the exact same route under the same circumstances, in my congested residential neighborhood with a lot of WIFI interference (most homes have 1-2 WIFI networks). Instead of 950 feet, about 1600 feet. I can't wait to use this in the open air and see what it can accomplish. You should be aware that when you fully extend the RC controls, your fingers or thumbs will contact the back of the signal booster's "bowls." When you are going fast, it's just a little bit crowded and requires some getting used to. The device is packaged well and has a plastic protective layer that you must remove before flying. I appreciate how it folds up into a neat, small box as well. very little Nice thing.
4.1/5
Antenna Amplifier / Signal Booster for DJI
Parabolic reflector is made of metal, usually a metal frame covered with wire mesh on the inside. The metal coating is formed to act as a mirror reflector radar energy.
Compatible with: DJI Phantom 2, Phantom 3 Standard/SE Remote Control
In the process of flying, it can not frequently lose touch with the DJI phantom 3 standard se
Boosters are attached so they will not cause the antennas to fall to the side like other products. They will stay in the perfect recommended upright position for maximum signal.
$234
Great results. The effectiveness of it shocked me. When I used it with my Phantom 3 Standard, the range was significantly increased. I experimented with this device in a rural area where the terrain was level and there was little interference. I completed two flights—one using the range booster and the other not. The distance between the two flights was 220 feet. The first flight without the extender climbed to a height of 2,850 feet before it lost signal and automatically descended to the ground. The second flight got as high as 5,700 feet before the signal went out. The impact of such a tiny, straightforward piece of plastic was unexpected.
3.3/5
Package Includes: 1 x 14dBi 5.8GHz Panel Antenna ,1 x 3dBi 2.4GHz Antenna ,2 x SMA to IPEX Cable , 1 x Blomiky Wipe
FPV Distance Enhanced for H ubsan H501S H502S H107D+ H107D JJRC H25G H29G
Assemble by yourself,to make 2 holes on the top of the controller, please check your controller before purchase
For instruction, please check Picture 3,Detail see video:http://www.youtube.com/watch?v=xek1xzgzgms
$234
This was bought for my H107D . Several items to consider are:These controllers lack the convenient ipex connector and instead use soldered connections for the 2.4 GHz antenna.Remember that you must cut and strip the antenna wire; the ground is the outer mesh-like wiring, and there is a central wire that you must separate out and strip off as well before soldering each to its appropriate location (see pic - found on youtube)The controller images in the item description above are from another Hubsan quadcopter; the only other contents of the box are the parts. These same images serve as your only instructions.Overall, the tweaks appeared to have been beneficial, however I will do some better range tests once it warms up outside.
COPYRIGHT © 2019
