Best Puller Sets in 2022

Last update: December 14, 2022

Are all crank pullers the same?

Not all crank pullers are the same. Some are designed to work with specific types of cranks, while others are more universal. There are also some crank pullers that are designed to be used with a specific type of bottom bracket.

How do bearing pullers work?

A bearing puller is a mechanical device that is used to remove bearings from their housings. There are many different types of bearing pullers, but they all work in essentially the same way. The bearing puller consists of a body, a jaw, and a screw. The body of the bearing puller is attached to the housing of the bearing, and the jaw is inserted into the bearing. The screw is then turned, which causes the jaw to expand and grip the bearing. The screw is then turned in the opposite direction, which causes the jaw to contract and release the bearing.

How do I choose a bearing puller?

There are a few things to consider when choosing a bearing puller. The first is the size of the bearing. The second is the type of material the bearing is made from. The third is the amount of force required to remove the bearing. The size of the bearing is important because it determines the size of the puller. The type of material the bearing is made from is important because it determines the type of puller. The amount of force required to remove the bearing is important because it determines the size of the force required to remove the bearing. The size of

How do you remove gear without a puller?

If you don't have a gear puller, you can remove a gear by heating it up with a torch and then hitting it with a hammer.


Seven Sparta Car Air Wedge Pump Kit, 2 PCS Air Wedge Bag Leveling Kit & Alignment Tool Inflatable Shim Bag with 3 Tools for Home Use and Auto Repair Review:


This is a backup product. This gadget will enable you to regain entry if you accidentally lock your keys in the car. It's an inflatable wedge with a hand pump that fits between the door and the frame so you can reach through and unlock the door by slightly separating them. Additionally, it can bear a good deal of weight, which makes it helpful for moving furniture.



ARES 71002 - Harmonic Balancer Puller Set - Remove Damper Pulleys in Tight Engine Compartments Without Removing The Radiator - Storage Case Included Review:


Due to the cost, I was a little reluctant when I decided to purchase this to replace the oil pump on my 6.2. Since I work as a mechanic, I'm accustomed to using Mac, Matco, and Snap On tools. I needed this for use at home because the other options would have cost more than I intended to spend.Don't be alarmed by the price—this is a HIGH-QUALITY instrument! I would anticipate quality from one of the three previously stated. It precisely executed what it was supposed to do! It might be very challenging to remove the balancer from these LS motors. They are simply too tight to be removed using "cheap" tools. This one really did work well! Good quality threads in the center, never slipped off. The threads are tightly woven, as they should be.You can use a 3/4 wrench, 3/4 socket, or (and this is where this tool excels above the big three) a 3/8 ratchet by itself to drive it. The threaded rod's end has a 3/8 female receiver where you may attach your ratchet. You have no idea how wonderful that is.The case, which is a typical blow-molded plastic case, does a good job of holding the tool.I do advise you to oil the threads using an extreme pressure grease tube. Besides safeguarding the threads, makes tools like these work so much more easily.The Quicksilver extreme pressure grease is what I use. It is the best I have so far discovered.Thank you for the high-quality, reasonably priced tool that was made in America!



United Pacific 90010 Chrome 31" Fifth Wheel Pin Puller Review:


At truck stops, $20 to $25. I'll say it again: This finish is outstanding. Reach is good because my arms are short, and it's really well crafted, making it a great purchase. I rarely need the straight notch-hook version, so use this one instead. It's hard to beat for the price, too. Yahoo!! This was 15.95 when I purchased it on April 1, 2018.



ARISD Car Air Wedge Pump Wedge Kit – Leveling Kit & Alignment Tool Inflatable Air Shim Bag for Home Use and Auto Repair Review:


For the most of my 20 years in the car industry, I worked at dealerships. When necessary, this kind of gadget—along with a long arm tool to reach a door lock—is highly beneficial.This can assist you in getting back inside a locked car if you, a family member, or someone at work becomes locked out.Two wedges are included in this kit, one of which is large enough to be used as a lever to create a larger opening in the door seal. To hold this place open and free up both of your hands, insert the pump wedge air bladder once you have a space of around 1/4 inch. The next step is to obtain a long arm tool (also available on Amazon) to reach a door lock switch or an interior door handle in order to access the car.Be careful not to rip the frequently fragile rubber/foam seal between the door and the car's body or scratch the paint of the vehicle. In order to determine where there is sufficient flex in the door assembly to let the inflatable wedge in, you'll also want to test the wedge on a few different regions of the window (usually the top of the window is the best way to obtain access). Also bear in mind that there is no point in purchasing this kit if you don't have a long arm device with a hook on it (a coat hanger could serve in a pinch but isn't ideal).Here is the one I purchased: I chose this over the one piece because these items are frequently 4 feet long, which makes them difficult to store in certain cars' trunks, where I prefer to keep mine in case someone else needs it.It's ideal to keep one of these in a convenient location if you or a coworker frequently lock yourself out of their automobile. The first time you use it, it will more than pay for itself because you won't have to wait for help from AAA or anyone else. If nothing else, it's worth it to be able to avoid the humiliation of a self-inflicted lockout!Although I haven't tested it yet, this device seems to be reliable. I gave it four instead of five stars simply because of this. I'll try to report back with that information if it fails or goes on for a while. FYI, the business requests "a objective assessment (Positive/Negative)" and promises to send you a free gift item you choose from six alternatives. No matter positive or negative, they say. So I'm testing that, making sure this review is published, then watching to see if the product I choose shows up. Since it's a choice for the free item as well, I'm going to purchase another of the same kit! I'll always have one on hand because that one is going in my second car.



CARTMAN Slide Hammer Puller Set Review:


So, that truly did work. It has now been used to replace bearings in two of my cars. I will admit that it didn't take just "4 whacks and done"; I had to pound the hubs and bearings out for quite some time. Therefore, even though it wasn't as simple in my case (both cars had over 170K miles), it did function and endure the hours of use. However, I will undoubtedly purchase a 10 pound to utilize on the following bearing. To use with my adapters from this kit, I'll purchase a ten pound coin similar to the one in the following link: https://www.amazon.com/dp/B000FN2VX6/?coliid=I30VVTUJUEEMQY



Lisle 46950 Relay Puller Pliers Review:


These pliers function so much better when long nose pliers are used, but you must still pay great attention to how the relay is gripped as you pull it out. Try to get it close to the relay's base and squeeze gently—enough to prevent it from coming out from under, but not too hard that you bend the tips. excellent value for the money. There should be no bend in the handles. The grips slide off because of the handles' curvature. You feel a little confused as you try to control the grip pressure.



OrionMotorTech 9-Way Slide Hammer Puller Set, Front Wheel Hub Bearing Remover & Rear Wheel Axle Shaft Puller Tool Kit Review:


This sliding hammer is very durable. I used it to remove our GMC Acadia's wheel bearing hubs. Due to the iron (steel) hub and the aluminum bracket that its flange fits into, they were crammed in very tightly. Iron and aluminum react aggressively to one another when they come into touch, creating the appearance of being welded together. An old wheel bearing hub was fitted with two rotors before being put onto the slide. I increased the sliding weight by 55 lbs, bringing the total to 60 lbs. This item only had a 5 pound slide when it was purchased, so adding 60 lbs should have destroyed it, however despite all that abuse, it still maintains its nice appearance. I'm not sure what it would take to break this, but I am confident that I am not capable of doing so. Fantastic product!



8MILELAKE 9 Way Slide Hammer Axle Bearing Dent Hub Gear Puller Set Review:


My friend Ray helped me with some electrical work, so when I wanted to pay him (he never takes money), he wanted this equipment, which I'm still not sure what it is. I purchased it, and Ray said it made the task much easier. He was performing maintenance on an ancient car's brakes. He emailed me this picture (I guess he thinks I now get it). Ray's word is as good as mine, so if he says something is fantastic, it probably is.



ARISD Auto Paintless Dent Repair Kits - Adjustable Gold Dent Lifter Dent Repair Tool Kit,Pops a Dent puller Kit for Car Hail Damage Repair and Car Dent Removal Review:


IT PERFORMS! I recently acquired it and made my first two dents. It takes some skill and practice, but I'm really impressed. I must admit that I initially believed that this would be one of those "seen on TV" gimmicks. NOT AT ALL! Like I said, with a little effort and dexterity, I was able to make my first two completely vanish. One thing I should mention is that I have a Pro Heat Gun (2 tries on each as I am learning). The glue sticks that come with it have a thickness that is roughly half that of mine. I simply used the TechBond glue stick that I already own, and it performed well. I'll purchase a unique glue gun particularly for this use. I'll say this as my final statement. This item WAS NOT given to me for free or even at a discount! I made FULL payment. I'm just a regular Pennsylvanian "man," nothing special.



8MILEAKE Blind Inner Bearing Puller Hole Remover Extractor Set Slide Hammer Tool Kit Review:


After removing two bearings from a tractor transmission, I was confident in my decision to buy. Good grade steel and threads make it simple to use. Compared to other kits that just contain the narrower-shaped expanders, the amount purchased for the race seems better. Yes, as other reviewers have said, the slide hammer could be longer and heavier, but it is still suitable for the kit's intended use. It's not an axle puller, and a B H may not always be the best option. The "T" pin at the slide hammer end broke out, but not enough to warrant a lower rating.


How many types of pullers are there?

There are three types of pullers: the shoulder puller, the arm puller, and the leg puller. The shoulder puller is the most common type of puller. It is used to pull the shoulder back into its socket. The arm puller is used to pull the arm back into its socket. The leg puller is used to pull the leg back into its socket.

What are puller sets used for?

Puller sets are used to remove bearings, gears, and other press-fit parts from a shaft. The puller set includes an extractor, which is inserted into the part to be removed, and a slide hammer, which is used to drive the extractor out of the part.

What are the main parts of a power puller choose three?

A power puller has three main parts: the engine, the transmission, and the drivetrain. The engine is the part that provides the power to move the vehicle. The transmission is the part that transfers the power from the engine to the drivetrain. The drivetrain is the part that turns the wheels of the vehicle.

What are the three types of pullers?

There are three types of pullers: 1. The screw puller is the most common type of puller. It consists of a screw that is inserted into a hole in the object to be pulled. The screw is then turned, which causes the object to be pulled towards the center of the screw. 2. The lever puller is another common type of puller. It consists of a lever that is inserted into a hole in the object to be pulled. The lever is then turned, which causes the object to be pulled towards the center of the lever.

What is a 2 3 puller?

A 2 3 puller is a tool that helps you remove nails from a board. It is also known as a crowbar.

What is a blind bearing puller?

A blind bearing puller is a specialized tool used to remove bearings from a shaft without damaging the shaft. The tool consists of a body with three jaws that grip the bearing, and a center screw that pulls the bearing off the shaft. The jaws are adjustable to accommodate different bearing sizes.