Best Powersports Speaker Systems in 2022

Last update: November 27, 2022

Are the MP694 waterproof?

The MP694 is not waterproof.

Can you put a Bluetooth speaker on a motorcycle?

Yes, you can put a Bluetooth speaker on a motorcycle. There are a few ways to do this, but the most common is to use a phone mount with an attached Bluetooth speaker. This will allow you to keep your phone charged and protected while you're riding, and you can control the music directly from your phone. There are also Bluetooth speakers that are designed to be mounted on a motorcycle, which may be a better option if you're looking for something more durable.

Can you put a sound system on a motorcycle?

You can put a sound system on a motorcycle, but it may not be the best idea. The wind and the vibration of the motorcycle can damage the sound system, and it can be difficult to hear the music over the noise of the motorcycle.

Can you put speakers on a ATV?

You can put speakers on a ATV, but it may not be the best idea. The speakers will be exposed to the elements and could get damaged or wet. Also, the sound quality may not be great since the speakers will be bouncing around while you're riding.


Bushwhacker UTV Speaker Mount - Universal Fit Attaches to Roll Bar Adjustable Strap Fits Most Portable Speakers - Side by Side Bluetooth Wireless Holder for Cage Attachment Accessory Secure Removable Review:


Such a great speaker mount. I've always had trouble listening to music while playing golf. The speaker kept toppling over, tumbling out of the cart, and landing in the basket. This attaches it and ensures that it is always in the ideal location. With no speaker limitations, the sound is much better. secures it firmly in place. The Oontz Angle 3 speaker that I use is securely held in place. The Speaker does not move at all inside the mount and does not fall down the cart roof braces. worth purchasing.



RoadPro RPSP-15 Universal CB Extension Speaker with Swivel Bracket, 2-3/4 x 4-1/2" Review:


I have to admit that this speaker sounds shockingly nice for the price considering that I work as a broadcaster and am surrounded by pricey professional audio equipment. Based on the evaluations I read here, I purchased two of them, and I wasn't disappointed.I use one with a Yaesu FT2900 ham radio in the car and another with a Yaesu FT8900 in my home. Additionally, I've used them with two various handheld scanners. In each of these instances, the mono 3.5mm (1/8-inch) tiny plug on the speaker suited the radios perfectly.No circumstance has arisen where I've needed to increase the volume above 25%–50%. The vocal quality is agreeable and not at all harsh, with a nice mid-range tone that is neither too tinny nor excessively boomy. All four of the aforementioned radios sounded better thanks to this speaker; in fact, I'd say they all sounded very similar after using it.Due to its size and weight, it is the perfect choice to simply clip it in place and relocate it as needed. Both of mine are not permanently mounted because I prefer the mobility, particularly when I want to tuck one away in the center console.Although I can't really compare it to products with more well-known names, at $13, I think this is a 5-star purchase. I'd be happy to purchase more of these.



NOAM NUTV4 Quad - 4 Channels Marine Bluetooth ATV/Golf Cart/UTV Speakers Stereo System Review:


I gave the Honda 700-4 2016 four stars since it was a little challenging to install the speakers to the roll bar using the provided rubber spacers. I tried pessing the speaker and mount together while on the bar to get the speaker bracket screws to catch, but there wasn't enough length in the screw; if they had made the screws a little bit longer, it would have made for a tighter fit. I had to remove a rubber spacer in order to get the screw to catch, but that left some play in the speaker mount. There isn't enough wire, which restricts where you can mount the amplifier unless you want to go out and buy more wire. Fortunately, I was able to mid mount the amplifier on my Honda and run the wires as shown in the pictures without having to drill any holes, which works fine. You could theoretically adjust the speaker by pulling it and rotating it around the rollbar, so make sure you use the appropriate spacers for your size rollbar. All four speakers' audio quality is quite good. I used the equalizer on my phone to give a little bit more bass; you might want to add a subwoofer, however this suited our needs and added a respectable cost. Additionally, I did not need to add an accessory switch because the amp already has an in-line pushbutton switch that makes it simple to turn off from where I put the app. You are welcome to ask any queries.



NOAM NUTV4 - Marine Bluetooth ATV/Golf Cart/UTV Speakers Stereo System Review:


Fantastic tiny speaker and amplifier set! The ones I installed on my RZR 1000XP are almost flawless. The amp is tiny enough to go up under the dash, but if you want to use it on a UTV, you'll need to create a mounting solution. I created a mounting plate to fit existing standoffs beneath the dash. The installation process was generally simple. Due to the weather I would be riding in, I did cut out the provided switch and solder/heatshrunk all connections, including the ones to the existing speaker terminals. However, because this amplifier will remain on as long as power is given, it is crucial to put a switch in the power line.The amplifier is well constructed. If mounted firmly, the aluminum enclosure appears to be sturdy enough to withstand some trail riding. Excellent speakers are present. Despite being made of plastic, the mounts should work perfectly due to the speakers' light weight and bracket design. In order to obtain a secure fit on a stock RZR roll cage, I did need to quadruple the rubber bracket inserts. To prevent being pulled out by an errant tree branch, speakers are securely fastened and tucked into the frame. The controller is decent, and it feels like the rubber ring can sustain prolonged use.Cons: At this point, the waterproofing on the control board is the only drawback that bothers me. Although the product appears to be made to keep the elements out at first, the board started having problems after a day of riding through a creek with around 2-3 feet of water. This control module houses all of the circuitry for Bluetooth and amp control. I took the controller out and got to work looking. I discovered the problem after disassembling the controller. The control module had a fair amount of dampness. Although the board is well-designed and seems to have been waterproofed with an epoxy spray, the buttons have a little space in the bottom that lets air out when the button is pressed. This caused my "Volume Down" button to stick by allowing moisture to enter the button. I made sure the board was completely dry and used some contact cleaner to prevent the buttons from corroding before attempting to locate the leak. I should mention that the controller's placement made sure that it only occasionally received a little mist of water, thus submersion wasn't a concern. Following some consideration and a quick reassembly to identify a potential weak spot, I focused on the 1/8 stereo plug jack on the front of the device. If you choose not to connect via bluetooth, this is essentially a hole carved out of the rubber ring that allows you to plug in a line-level connection. Since it is useless for my bluetooth connection, I was initially going to close it up, but I decided to try making it waterproof instead. I reapplied the rubber surround after sealing the jack with a small coating of silicone sealant, pressing the rubber into the sealant to make sure it made contact but didn't obstruct the button's functionality. To prevent moisture from entering the unit from that side, a small dab of silicon was applied to the end of the jack. Once the silicone had dried, I put everything back together and tested it. Unit currently operates without a hitch. I will as soon as possible retest the control board under the identical circumstances and update if the issue reappears. The device will be impenetrably solid if I seal this jack closed.In conclusion, this product is excellent for my use. Don't expect to shake any fillings loose with the amount of bass because the speakers are only 4" in size, but the sound quality is greater than I anticipated given their diminutive size. enough volume to be heard when cruising. In my opinion, the control board needed a few minor tweaks, but I'm not sure you could have created a better product to cater to the UTV market. I would strongly advise anyone willing to put in the effort to install it properly to do so!



GoHawk RE9-X Waterproof Bluetooth Wireless Motorcycle Stereo Speakers 7/8-1.25 in. Handlebar Mount MP3 Music Player Audio Amplifier System Scooter Bike ATV UTV, USB, AUX, FM Radio (RE9-X Silver) Review:


The best money I've spent thus far; however, it probably won't be audible at 70 mph on a highway. However, I can hear it clearly as I travel at 5 to 10 mph on my ATV through the woods. This device is incredible for either an ATV or a UTV; it's just wonderful. I can keep my phone in my pocket while the Bluetooth is on and listen to Pandora, iHeartRadio, or just the radio. What's nice is that when a call comes in while the Bluetooth is on, it will immediately notify me on the screen. Normally, I would miss that call while riding down the trail, but because the Bluetooth is connected, I now know one of my friends is calling me looking for me or the person behind me broke down. If you purchase this, my sole recommendation is to note the plastic bits that are included. Little plastic compression nuts prevent things from being tightened too much. When you start putting it together, you'll understand what I mean when I say that it's difficult to fit on your handlebars and get it just right with everything else that's on there. It sometimes requires assistance to hold it in place while you tighten the screws on; just be careful not to overtighten everything. When I really, really want to give it a bath, I'll use the pressure washer. I don't know how it will function for motorcycles on the road, but I like this one too much to not recommend getting one. When it comes to my ATV, I had heard some unfavorable evaluations, but I'm pleased I chose not to take their advice.



GoHawk TJ4-R Amplifier 4" Full Range Waterproof Bluetooth Motorcycle Stereo Speakers 1 to 1.5 in. Handlebar Mount Audio Amp System Harley Touring Cruiser ATV UTV RZR, AUX, FM Radio (TJ4-R Black) Review:


Prior to my current purchase, the TJ4-R, I encountered three problems, of which two were not the company's fault. The TJ4-R is a fine system overall, but it wasn't as loud as I would have liked. Because of where I placed the cable, the remote's wire got cut in half. While those might be disregarded, the speaker bracket did fail on me.I replaced the TN4-R with one I purchased. WAY LOUDER The brackets are the same, though. I think the material could be beefier, but I also believe that I tightened the clamps too much. This time, I also paid more attention to the points where my cables touched the frame. Additionally, I would advise making sure the gaps on either end of the speakers are uniform and that the clamps are just snug enough to prevent slippage while attaching them to the handlebars.The TN4-R is far more enjoyable than the TJ4-R.



Design Engineering 050330 Boom Mat Speaker Baffles, 6.5" Round (Pack of 2) Review:


A baffle is not always only a weatherproof covering. The same applies here—you can't just place any speaker in any box. This 6.5-inch speaker baffle was 2.75 inches deep and 5.25 inches wide. Using the volume of a cylinder calculator, this results in a volume of 60 cu inches, which is, of course, without any volume loss to the speaker's frame and magnet. You must open the back of the baffle if your speaker needs more volume, which the majority of them need. If you don't, your speaker will sound more sealed. This baffle can work if you require that tiny enclosure volume. You will need to drill a relief hole, open the back, or create a more involved custom door (pod) to meet needed speaker volume because many speakers just demand greater volume (whether sealed or ported). I opened up the back door even though I had an open back door pod since there wasn't enough volume. So I feel bad for anyone who needs to install a 6.5" woofer directly into a door panel. The product image gives the impression that a 6.5-inch speaker may be inserted into this baffle, however this seems to be deceiving. The baffle is only created big enough for the smallest speaker frames, or smaller speakers like a 5.25-inch. In the end, I had to fill it with fiber fill since I had to reduce the back piece to allow for window clearance. This did reduce bloated bass brought by by the 6.5" and 8" woofers sharing the same door.



Design Engineering 050380 Boom Mat Speaker Baffles, 6" x 9" Oval (Pack of 2) Review:


Get the skinny line for sure! The reviews for the 6"x8" edition of this product were the reason I ordered this size, and they were accurate. For my Pioneer TSD6802R speakers, this depth and hole size are ideal—any larger would have an excessively huge internal diameter, and additional depth is unnecessary. We'll have to wait and see how long it lasts, but it seems to be exactly as thick and durable as the 6"x8" XTC baffles I used for another set of speakers.Update: I put these in the front doors of my 2004 Ford Taurus. These are the slim line, and they absolutely match the depth of my Pioneer speakers (there is no gap between the rear of the magnet and the bottom of the baffle), however they are still somewhat too deep. When the window is rolled down, the back of the baffle only just barely touches the window in the final 6" or so of its travel. It merely causes a pleasant squeak as the glass rubs against the foam; it has no effect on how quickly or slowly the window travels. My Pioneer speaker has the same depth as the factory speaker, so it's not the fault of this baffle; it's simply amazing how little room Ford allocated for their door speakers. I'm not sure if I will remove the bottom of the baffle to solve this problem because doing so will largely contradict the purpose of the baffle - or if I will simply put up with the squeaking.



LEXIN LX-S3 Motorcycle bluetooth speakers with FM Radio Antenna, Waterproof Motorcycle Stereo Radio Systems fit 0.87 to 1.25 inch Handlebar, 3 inch Chrome Audio Amplifer System Review:


Overall, in my opinion, the quality and features for the price simply cannot be matched.comes in top-notch packaging. except that I connected the battery using alternative connectors, which is included. But if you don't want to pay $0.73 at the hardware shop, you can use the ones that are already provided. There are numerous sizes of rubber and plastic clips included for mounting the speakers to any handlebar size you may have. All wires are completely attached and long enough for waterproof use. The positive and negative power wires are the only two that need to be installed. All other connections are either proprietary or run into the speakers. When connected in, the USB will charge quickly enough for the phone to maintain a full charge even with the music app, Bluetooth streaming, and live Google Maps open. The antenna should be mounted as far back as feasible on the motorcycle, according to the manufacturer. I rushed it to the front fender, where it is hidden between the headlight and the windshield, because I was cold and impatient. It took me an hour to complete it. However, because of my disability, I was unable to fully crank down the right side speaker/bolt. I took my time as well. Also take note that I didn't run the antenna all the way through the bike to the back. I own a Suzuki Intruder 1500C from 2002. Had I taken off all the components to properly and securely cover the wire, the installation would have taken at least an additional hour.Use is also quite good. The button is held down for two seconds. It will indicate Bluetooth readiness. If you have the phone nearby and have previously established a connection, the music begins playing in less than a second. swift and simple. Press the FM button. Change stations up and down by using the left and right arrows. A "seek" button it. So if you enjoy channel surfing, it can be a little bothersome. Even the channels you detest halt at each one. So I'm listening to 92.5 in Cincinnati. They perform vintage rock. I simply exit the station on my own. Bluetooth is fine because I've already created some incredible tunes on my phone. Additionally, I haven't yet opened the "IHeartRadio" app while on the bike. There are a thousand live-streamed radio stations there. Using it might or might not be simpler. When I'm riding my bike, I keep my iPhone connected to the USB port, but I don't use it to play music. I've discovered through the years that using that strategy in a car is annoying. A bike is not, I'm certain of that. There is no AM radio; only FM. In my neighborhood, the reception is really good. Contrary to what many reviewers would have you believe, the volume is superior. It's not as loud as my friend's 2018 Harley, which has four 6"x9" speakers and a powerful amplifier. On the rare occasions I do take the highway, I can still hear it clearly. Although not the loudest stereo I've ever heard, it is loud. It does, in my honest opinion, sound better than a $100 system ought to.I made a few crucial considerations before opting to buy this particular one.There isn't a display on it. The station you are on cannot thus be seen. That would unquestionably be a major benefit.It doesn't function using a keychain. With the speaker's knob, you may effortlessly lower the volume. Additionally, you may rapidly turn the knob to silence it. A keychain requires fidgeting, thus I believe using one would be challenging and risky. That played a HUGE part. It is incredibly practical and, in my opinion, considerably safer to have all of the settings immediately accessible on the handlebar. You can't actually utilize the keychain if your key is linked to the side of your bike. You could probably use Velcro to secure it to the tank, but be honest. Who has a bike they detest that much?The rating was the third factor I thought was crucial. I couldn't find a five star hotel for less than $300. But in that price bracket, this has one of the highest.In general, if you don't have an unlimited budget, I would suggest this. You need a full wardrobe and some hard bags so you can attach large speakers if you really want to scream out some loud music. What a large sum of money. As fantastic as anyone I ride with, the sound is. Even though it isn't perfect, the price and quality are unbeatable.


How can I make my motorcycle speakers louder?

If you're looking to make your motorcycle speakers louder, there are a few things you can do. First, check to see if your speakers are mounted securely and that all the connections are tight. If everything looks good there, you can try adding a amplifier to your system. This will give you a boost in volume and can really make a difference. Finally, make sure you're using good quality speakers. If your speakers are low quality, they just won't be able to produce the volume you're looking for no matter what you do.

How do you wire up a motorcycle amp?

Most motorcycle amps are powered by the bike's battery, so you'll need to connect the amp's power wire to the battery. Once the power wire is connected, you'll need to connect the amp's ground wire to a metal surface on the bike. After the ground wire is connected, you can connect the amp's speaker wires to the bike's speakers.

How many channel amp do I need for 4 speakers?

If you have four speakers, you will need a two-channel amplifier.

How many watts do you need for a motorcycle stereo?

A motorcycle stereo typically requires between 20 and 200 watts of power. The wattage you'll need depends on the stereo's features and how loud you want to play your music. If you're looking for a powerful stereo system that can get loud, you'll need at least 100 watts.

How many watts is good for motorcycle speakers?

There is no definitive answer to this question as the wattage required for motorcycle speakers will vary depending on the make and model of the motorcycle, as well as the preferences of the rider. However, as a general rule of thumb, speakers with a higher wattage will be able to produce louder and clearer sound than those with a lower wattage. Therefore, if you are looking for motorcycle speakers that will provide high-quality sound, it is generally advisable to opt for those with a higher wattage.

Should amp wattage be higher than speaker?

The wattage of an amplifier should be higher than the wattage of the speaker. This is because the amplifier is responsible for providing the power to the speaker, and the speaker needs more power than the amplifier.