Yes, Gorilla Glue works on metal to metal. I have used it myself to glue metal to metal with great success. The key is to make sure that the surfaces are clean and free of any grease or oil before applying the glue. Once the glue is applied, it will create a strong bond between the two surfaces.
You can use a product called a concrete screw. Concrete screws are made to go into concrete without the need to drill a hole first. You simply drill a pilot hole into the concrete with a regular drill bit. Then you screw the concrete screw into the pilot hole. The concrete screw has a special thread that cuts into the concrete and anchors the screw in place.
There are many ways to bond metal to metal without welding. Some common methods are soldering, brazing, and adhesive bonding.
Joining two pieces of metal without welding can be done by using a fastener such as a screw, nut and bolt, or rivet. Another method is to use adhesives, which can be either temporary or permanent.
4.6/5
Use for pool and SPA repairs (plaster, gunite or fiberglass), Boats, RV, Auto, at work and around the house
Easy to Use 2 part hand moldable epoxy putty hardens in 50-60 minutes with final steel hard cure in 12 hours
Made in the USA
Can cure underwater
Use on all types of plumbing fixtures and ceramics, tubs, toilets, sinks, tiles, caulking, fiberglass, sculpture, taxidermy, doll repair, carving, metal, pump housing, pool decks and broken tiles
$234
I acquired it because water was dripping through a few holes in the plaster of our in-ground pool and down the sides to the bottom. I was searching for a remedy so I wouldn't have to drain the entire pool because the cracks were so deep. I made the decision to try it because the box claimed that it cures underwater.The sample I made out of the water cured in an hour, but the material I put underwater remained soft after a few hours, which initially scared me a little. However, it became noticeably more difficult after roughly a day.A month later, the pool is now leak-free and the epoxy is extremely durable. This is fantastic stuff.
4.5/5
Handle parts in ten minutes
Five minute working time
Made in the USA
Proud Sponsors of Wounded Warrior Project
$234
Although this epoxy is simple to use, I have found that the hardening and curing times are longer than I had anticipated. When blended, it starts off as a thick liquid, similar to honey. It becomes thicker and stickier after 5 minutes; this is roughly the maximum working duration. After an hour, it will have solidified and provide a respectable amount of strength, although it will still be rather sticky and chewy. It takes a few days, in my experience, for it to completely lose all of its softness and acquire its final hardness and strength. Only my experience; yours might be different.I'm happy with this epoxy other than the longer-than-expected cure period. I applied a little test quantity to a piece of glass, and after two days, I was unable to chip it off. It adheres to glass quite effectively. The majority of the polymers I've tried, though, did not create a lasting link with it. A specialized plastic adhesive is needed to connect many polymers since they are notoriously difficult to bond.While the hardener (red container) has an unpleasant scent, it happily goes away by the time the mixture is completely set. The epoxy resin (black bottle) has almost no smell. The little tops should be tied like on plastic condiment bottles because they are easily lost.In comparison to cyanoacrylate/super glue, this 2-part epoxy is expensive and requires some effort to mix, but you get a lot for your money and it doesn't solidify in the bottle, so it has a long shelf life. Super glue, water-based glue, and polyurethane glues are unable to perform several tasks that this glue can. I'm happy to have it whenever I run into a repair around the house that calls for it.
4.3/5
Strong, permanent, fast and gap-filling; great for multiple surface applications
Best for tough repairs requiring a durable bond, gap-filling and solvent resistance
6 minute set; plenty of repositioning time for the perfect fit
Easy-to-use syringe; separate barrels of resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses
Dries clear; ideal for clean, easy finishing
$234
I thought I would attempt this because I was seeking for a different way to bond copper pipe for non-potable reasons than soldering or torch welding. (I sincerely doubt that this is secure for water pipes.) The silicone epoxy and wood glue from the Gorilla brand have all worked well for me in the past.The instructions advise that the resin and binder should be combined for 20 seconds before being used because it will work best if used right away. It recommends using the plastic insert packing as a mixing palette. The syringe device is supposed to be closed with the help of a small black plastic tab.Well before the 5-minute time limit, this material had already dried to the point of being unusable. However, I believe that the environment has an impact on this number. Since there are no monsoons where I reside, the humidity in the summer is relatively low. (Paint, for instance, dries extraordinarily fast!) In order to overcome the drying period, I had to adjust by working quickly.I put off working on my project for a few days. I then tried to peel it apart but couldn't manage it. Everything is secure and seems to be permanently linked!It works with copper pipe tubing and fittings, which is good news!The bad news is that it dries rapidly in a dry, hot atmosphere and is untidy.
4.2/5
Best for tough repairs requiring a durable bond, gap-filling and solvent resistance
Dries Clear; Ideal for clean, easy finishing
Strong, permanent, fast and gap-filling; Great for multiple surface applications
5 Minute Set; Plenty of repositioning time for the perfect fit
Easy-to-Use Syringe; Separate barrels of resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses
$234
I thought I would attempt this because I was seeking for a different way to bond copper pipe for non-potable reasons than soldering or torch welding. (I sincerely doubt that this is secure for water pipes.) The silicone epoxy and wood glue from the Gorilla brand have all worked well for me in the past.The instructions advise that the resin and binder should be combined for 20 seconds before being used because it will work best if used right away. It recommends using the plastic insert packing as a mixing palette. The syringe device is supposed to be closed with the help of a small black plastic tab.Well before the 5-minute time limit, this material had already dried to the point of being unusable. However, I believe that the environment has an impact on this number. Since there are no monsoons where I reside, the humidity in the summer is relatively low. (Paint, for instance, dries extraordinarily fast!) In order to overcome the drying period, I had to adjust by working quickly.I put off working on my project for a few days. I then tried to peel it apart but couldn't manage it. Everything is secure and seems to be permanently linked!It works with copper pipe tubing and fittings, which is good news!The bad news is that it dries rapidly in a dry, hot atmosphere and is untidy.
4.2/5
Bonds many materials, including fiberglass, concrete, many metals, glass, ceramic, and rubber
N/A
High-tack paste can be used in vertical and overhead applications
Two-part marine epoxy adhesive paste bonds materials in dry, wet, and underwater environments
Made in USA
Resists mild acids, caustics, detergents, gasoline, fuel oil, and fresh and salt water
Can be used in indoor and outdoor applications, with a temperature range of 35 to 115 degrees F and a service temperature range -20 to +200 degrees F
$234
There are times when I wish I could save a "Six Star" rating just for a product that I really like. One of those moments is now. I have mixed and used a number of epoxies, but I am VERY delighted with this one. It is consistently excellent enough to work. easy to blend Easy to use. Happy pot life. sets quite firmly. adore itMy primary responsibility was to fix a hairline crack in the fiberglass tank of a pool filter, which had to withstand pressure of up to 20 psig. I added a fiberglass cloth to the epoxy's interior to strengthen it. I hammered to form and adhered with epoxy four steel strips crosswise over the fracture on the outside (really the bottom of the tank), which had to withstand tensile stress. I then coated the area with extra epoxy. I anticipate getting several more years of use out of the filter because the repair is holding up well.It has also been utilized for a number of other fixes. Complete satisfaction.
4.1/5
Bonds many materials, including fiberglass, concrete, many metals, glass, ceramic, and rubber
N/A
High-tack paste can be used in vertical and overhead applications
Two-part marine epoxy adhesive paste bonds materials in dry, wet, and underwater environments
Made in USA
Resists mild acids, caustics, detergents, gasoline, fuel oil, and fresh and salt water
Can be used in indoor and outdoor applications, with a temperature range of 35 to 115 degrees F and a service temperature range -20 to +200 degrees F
$234
used numerous times for use in the hottest circumstances that motor vehicles can provide. If you adhere to these guidelines, it's a highly robust and long-lasting repair:1. The area must be free of grease and rust. With any reliable solvent, first remove the grease. Use a drill and a wire wheel to remove the rust. Metal needs to be spotless and shining.2. Use a mini-grinder with a cut-off wheel to rough up the area.3. Remove a sufficient amount of epoxy. Rub your hands together like you're trying to roll a snake by using only your bare hands. Roll another snake after folding the first one back on itself. Repeat this motion continuously for two minutes.4. Pinch a tiny piece off, then spread it on the surface. Push firmly and spread. Remove it, then spread more on the surface. It will eventually stick and not come off. Apply this to the entire area where you want the epoxy to be applied. It shouldn't take more than a minute to complete this.5. Lastly, spread the remaining epoxy over the area. Press, draw the edges inward, press once more. Continue doing this until the edges stay put.Use a scrub brush and a decent hand cleanser to clean your hands.Dry out overnight.
4/5
For use with all types of epoxies and phenolic resins
Epoxy mold release
It allows for a clean removal of the cured epoxy
Non-Silicone
$234
The effectiveness of this product astounded me. I used this for creating an epoxy river table, and the epoxy came out of the mold wonderfully! I'll use this every time, without a doubt.
3.8/5
DURABLE HIGH GLOSS FINISH: Cured epoxy is UV-resistant, 100% waterproof, resists blemishes, dings, heat, scratches, stains and yellowing
SUPER CLEAR: Total Boat Tabletop Epoxy cures crystal clear for superior finishes on bars, table tops, counters plus art & woodworking projects
EASY TO USE: Simple 1: 1 mix ratio, 2 part pourable epoxy coating is self-leveling, and cures smooth as glass at room temperature with no blushing
IDEAL FOR BOTH DIY AND PROFESSIONAL USE: 2 Quart kit includes 1 Quart resin & 1 Quart hardener
WIDE RANGE OF PROJECTS: Pro results on wood, metal, stone, ceramic and concrete tables, bar tops, countertops as well as embedding objects, decoupage, casting & other crafting projects
$234
April 2019. I mixed everything together precisely and successfully poured it over the formica bathroom counter. I did make a ring when I placed a cup of hot coffee on it too quickly. About 4 days after the pour, so it was clear that it hadn't fully built up yet. Before pouring, we painted the surface.I therefore painted our fiberglass shower pan before mixing the remaining epoxy. Very bad. Even though I had previously been very precise, the volume of what was left in each container was not exactly the same. The shower was thus really tacky. Now what? A firm representative responded to my Facebook message with sympathy but essentially replied, "Too bad." I honestly believed I would have to completely tear down the shower, but I chose to get in touch with the business again. I received their expert this time. He advised mixing it up before "painting" it over the tacky areas. Viola! It succeeded. I could have taken pictures, but all they would have captured is a shiny epoxy pour.
3.8/5
DURABLE HIGH GLOSS FINISH: Cured epoxy is UV-resistant, 100% waterproof, resists blemishes, dings, heat, scratches, stains and yellowing
SUPER CLEAR: Total Boat Tabletop Epoxy cures crystal clear for superior finishes on bars, table tops, counters plus art & woodworking projects
EASY TO USE: Simple 1: 1 mix ratio, 2 part pourable epoxy coating is self-leveling, and cures smooth as glass at room temperature with no blushing
IDEAL FOR BOTH DIY AND PROFESSIONAL USE: 2 Quart kit includes 1 Quart resin & 1 Quart hardener
WIDE RANGE OF PROJECTS: Pro results on wood, metal, stone, ceramic and concrete tables, bar tops, countertops as well as embedding objects, decoupage, casting & other crafting projects
$234
Fast-drying epoxy is now widely available on the market. However, in some situations, such as when working with many surfaces, you need epoxy that dries more slowly so you have more time to realign parts. You then have a lot less options when that occurs.Just enough time is provided by this epoxy for me to repair a damaged violin pegbox. I'm aware that hide glue is frequently used to repair musical instruments in this way, but epoxy is a better option because it's robust and simple to use, unless you need to consider the possibility of future disassembly. This epoxy provides just enough time to do such tasks. The setup period lasts between 45 to an hour.
2.4/5
Gel
Bonds metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone
Resistant to solvents, moisture and impact
Can be combined with fiberglass cloth for a durable patch
Water resistant, clear and permanent
Ideal for vertical surfaces and overhead repairs
Epoxy
$234
Using Loctite. It works. Read the guidelines. Verify if this is the best choice for you.I mounted some metal brackets with it under a granite countertop. 20 minutes of clamping time. waited 24 hours before using (full-set).
You can stick metal to concrete in a few different ways. One way is to use an adhesive. There are many adhesives on the market that will work for this application. Another way is to use mechanical fasteners. This would include things like nails, screws, or bolts.
Metal epoxy is a two-part adhesive that is used to bond metal to metal, or metal to other surfaces. The epoxy is mixed together and then applied to the surface to be bonded. It sets quickly and forms a strong bond.
Metal putty is a type of putty that is used to fill in gaps or cracks in metal surfaces. It is made from a mixture of metal powder and a binding agent, and is available in a variety of colors. Metal putty takes longer to dry than other types of putty, and is typically left to dry for 24 hours before being sanded or painted.
Metal epoxy putty is a strong, durable material that can be used to repair metal surfaces. It is resistant to high temperatures and can be used on both ferrous and non-ferrous metals. Metal epoxy putty can be shaped and molded to repair metal surfaces, and it can be sanded and painted to match the surrounding area.
JB Weld is a two-part epoxy that can be used to repair metal, wood, and plastic. It is typically used to repair cracks, holes, and leaks. JB Weld is a stronger and more durable alternative to traditional epoxy.
Epoxy putty is a permanent fix for many types of damage. It can be used to repair cracks, holes, and other types of damage. It is also a good choice for repairing damage to metal, glass, and other surfaces.
COPYRIGHT © 2019
