4.7/5
Temperature Resistant from -40 Degrees Fahrenheit to +212 Degrees Fahrenheit
Nitrile Tube Construction with 2 Spiral Polyester Reinforcement and PVC/Nitrile Blend Cover
Flexible and can be used for Cars, Trucks, Tractors, or Small Engines
Designed for Conveying Gasoline E85 Ethanol and Diesel Fuel
25 Foot Roll of 1/4" ID Black Rubber Fuel Line Made in the USA
$234
It appears to be of decent quality, but clean it thoroughly before connecting it to your motor. I connected it to a see-through filter and the motor and utilized around 20 feet of it in one run. It had a fresh filter. As I primed the line, I became aware of numerous little black particles in the filter. resembled flakes of rubber. I disconnected the line from the filter, primed it once more, and then reconnected it to a different new filter. Now seems to be running smoothly. The sole gas line connecting the gas tank and the filter was clean.
4.7/5
$234
There are different PSI ratings available for this. has NPT, which my neighborhood farm supply store does not. only has male connectors, but I can easily buy adapters from the same store where I buy the hoses. A really cheap way to maintain the hydraulic lines on my tractor. Since I use my tractor as a bulldozer, the OEM lines weren't very durable. These hoses have greatly simplified my life and decreased the cost of replacing lines. I paid local "specialists" to MAKE a number of hydraulic lines, but I afterwards realized that this was a waste of money. Considering how well the Apache line has consistently performed, I'm continuing with them.
4.6/5
25 Foot Roll of 5/16" ID Black Rubber Fuel Line Made in the USA
Temperature Resistant from -40 Degrees Fahrenheit to +212 Degrees Fahrenheit
Used for Cars, Trucks, Tractors, or Small Engines
Nitrile Tube Construction with 2 Spiral Polyester Reinforcement and PVC/Nitrile Blend Cover
Designed for Conveying Gasoline E85 Ethanol and Diesel Fuel
$234
I purchased this fuel line to use with my sailboat's marine diesel engine. Since my current fuel lines are adequate, I haven't installed it, but I wanted backup on the boat for when I'm out sailing. Although the hose doesn't include a USCG approval remark, a few of my acquaintances who work in the maritime maintenance industry said it is suitable for handling marine fuel. Your local marine retail store's comparable fuel hose costs at least twice as much. Simply since I haven't used it yet, I didn't give it five stars. However, following close examination and advice from what I would deem to be knowledgeable maritime service technicians, I am satisfied with this product.
4.6/5
Two factory-installed 3/4" male NPT fittings for attaching to couplings or equipment
Hose assembly for transferring gasoline with up to 15% ethanol, diesel, kerosene, or oil in manual pump or gravity flow dispensing operations
Nitrile synthetic rubber tube and cover for resistance to oil, solvents, abrasion, and weathering
Spiral synthetic yarn reinforcement for strength
8" internal strain relief springs on each end to prevent kinking at the coupling
$234
I'm not sure how effectively it serves the intended goal, but I'm happy with how it's performed thus far. On my 1998 Ford Ranger, I cut a piece to utilize as a replacement gasoline filler neck vent hose. I planned to finish the entire project over the weekend while I had the truck bed removed because the merchandise was ready for speedy delivery.
4.3/5
3/8-24 threads
Replacement part
Used to replace hose whip on Milton inflator gauge #506
Made in USA
$234
I got this to replace the standard design, long metal tube with a lens to read a gauge, on my Tru-flate inflator. If you purchased an inflator from Ace Hardware, it was presumably Tru-flate. Both the initial hose and this hose measure 1/4 "ID, but this hose is somewhat thicker overall despite the markings. Hose is 5/8" OD instead of the original 1/2" OD.As a result of the original hose's leaks and breaks, which prevented an accurate pressure measurement, I am now replacing it. This is a significant improvement, and I anticipate it lasting a long time. Several thingsThe 5/8 "Be sure that your inflator will take it because OD only just fit through the loop at the top of the device. Since this one fit so snugly and perfectly, I believe the thicker hose was intended for the initial design, but later on, to save money, they switched to a less expensive hose.Additionally, the place where the hose threads into the inflator on my old hose had an O-ring; if yours has too, be sure to save it because this hose is missing any form of seal or O-ring. Without some sort of seal on those threads as it is a straight thread and not a pipe thread, it may leak. Teflon tape might also work, but it would be preferable if you could use the O-ring from your old hose on the new one.Although the price of this item initially irritated me, the quality is clear when I hold it, and I am quite pleased with it.
4.2/5
Designed for Conveying Gasoline E85 Ethanol and Diesel Fuel
Temperature Resistant from -40 Degrees Fahrenheit to +212 Degrees Fahrenheit
25 Foot Roll of 3/8" ID Black Rubber Fuel Line Made in the USA
Nitrile Tube Construction with 2 Spiral Polyester Reinforcement and PVC/Nitrile Blend Cover
Used for Cars, Trucks, Tractors, or Small Engines
$234
as explainedAlthough I didn't need this much fuel line, purchasing it on a spool was less expensive than going to an auto parts store and purchasing the exact length I required.
3.6/5
Designed for use with all electric pumps
High quality Nitrile inner tube
Dispense diesel fuel, gasoline, kerosene, and petroleum oils
$234
There is nothing wrong with this hose at all. Even when it's quite cold outside, the hose is still flexible after a year of daily use.If the hose is pulled over sharp edges when pumping fuel, the exterior portion will not be cut. This hose is not at all bothered by the sun or warm temperatures. Is it kinkable? Yes. Swivel fittings are used for this purpose. It's not a problem or an issue. Pay a lot more money and avoid running over the hose if you must have a certified kink-free one. American made.
COPYRIGHT © 2019
