In the United States, there is no federal law that addresses the use of cell phone holders in vehicles. However, many states have enacted their own laws that ban or restrict the use of cell phones while driving. For example, California has a law that prohibits the use of cell phones while driving unless the phone is mounted on the vehicle's dashboard or windshield.
A magnetic phone holder is a device that is used to hold a mobile phone in place. It is usually made of a metal plate that is attached to the back of the phone case or phone. The plate has a magnet that is attracted to the metal on the back of the phone case or phone. This holds the phone in place on the metal plate. Most phone cases and phones are made of metal, so they are compatible with magnetic phone holders. If you have a phone case that is not made of metal, you can purchase a metal plate that is adhesive and stick it to
Yes, suction cup phone mounts work. They are a great way to keep your phone in place while you are driving.
Suction cups work best in warm weather because the warmer the temperature, the more malleable the rubber is. That said, they will still work in cold weather, but not as well. If you're looking to use a suction cup in cold weather, you can try heating up the rubber with a blow dryer before attaching it.
4.9/5
$234
I was not overly satisfied with the phone holder/gripper hand itself because the gripping power is only average. Instead, I combined the entire mounting tray with my old mounting magnetic part, made by wizgear. The magnetic puck of the wizgear is a direct fit for the ball/socket end of this mounting tray. It fits really well, gets very tight, and is soooooooooooooooo much better. Now, my phone is very secure, and I am VERY HAPPY.
4.3/5
Compatible with Passport X70 x80, Passport S55, Beltronics Vector 995, RX65, Most Rocky Mountain Phantom-T. *** (NOT COMPATIBLE WITH Escort Max series & New Escort iX Series) ***
Compatibility: S75 S75g S55, New Passport, STi Magnum, STi Driver, GX65, GX55, RX65, RX55, V6, V8, V10, V12, Pro 100, Pro 200, Pro 300, Pro 500, Vector 995, Vector 965, Vector 955, Newer Vector 940, Vector 895 & Express 795, Passport 9500ix, Passport 9500i, Passport 8500x50, Passport 8500, Solo S2, Solo S3, RD-5110 Passport 7500S, Passport 7500, 6800, 5000, 4600, 4500, and 4200
Unlike the one you received with your radar detector, this mount has a single extra large suction cup that's vacuum attached to your windshield or Your Dashboard (using the provided dash disk)
The mount has the metal clip that inserts into the radar detector with an adjustment point so that you can change the angle of the device
Brand New in ChargerCity NO FUZZ NO MESS Packaging
$234
I purchased this to replace the factory-installed small metal, two-suction-cup mount for my beloved Bell V995 in a work vehicle. The original may have caused the detector to shake the glass severely. The only reason the original version vibrates in this minivan is because the glass is angled differently than it is in my other vehicles, where it works just fine. First off, this mount shipped quickly and arrived as I would have anticipated in brand-new condition. The mount itself is strong and well-made, with a single large suction cup that is simple to attach. The part that extends into the detector should be made of metal, preferably metal covered in thin rubber for silence, but it is instead made of plastic. As others have said, I have my doubts about the plastic component's long-term durability in this particular location because it flexes, even though the rest of the mount is fantastic and rock solid. I've had the mount for a while, though, and haven't had any problems, even though I install and remove the detector every workday. I did have to cover the portion that goes into the detector with a small piece of ribbon to muffle it, but it's possible that this is because the vehicle vibrates more than most. The insertion piece could be improved, but even as it is, this product is still better than most. If necessary, I believe the insertion piece could be easily made at home, so there are no concerns. I would advise it.
4.3/5
Simple to use: Easy, one-handed use. Simply slide your glasses in and out of this handy sunglass holder. It could not be any easier. Plus, ReadiSpex Sunglasses Holders fold up flush against your dash when not in use, unlike the bulky car visor clips sold by everyone else!
Reliable, high-quality protection: ReadiSpex Sunglasses Holder is your in car glasses holder that provides a safe place to secure and protect your sunglasses or specs from getting lost, scratched or broken. Durable, all-metal construction looks better and lasts longer than those bulky, cheap, plastic car sun visor clips.
Quick installation with a strong, high-quality hold: Super-strong 3M adhesive that will stick to practically any surface; no screws or tools required.
Never lose or misplace your glasses or sunglasses again: With your ReadiSpex Glasses Holder, keep your glasses where you need them - within arm's reach - in your car, truck, home, boat, RV, and office
Fits all eyewear types: Universal fit accepts prescription glasses, reading glasses, sunglasses and more. It will hold multiple pairs of glasses too! And it makes a great holiday gift or stocking stuffer!
$234
For me, the ReadiSpex is a very helpful tool or gadget. I enjoy how the glass frames can be held and opened effortlessly because to the compact design. I place it close to my bed and in a discreet location that is both easy and accessible in my car. Since I don't have an eyeglass holder in my car, I can always keep my glasses in the same spot. I notice that when I put my glasses in my car, they often get covered, have stuff laid on them, or fall between the cracks. And I particularly enjoy using it on my nightstand because it serves as a post to the top, where I frequently knock them off. I no longer do.I also enjoy that I have a spare adhesive pad, which means that if I decide to change it, I won't have to worry about whether it will hold or not.I believe I have some fantastic ideas for Christmas presents and items to give to clients.
4.2/5
POWERFUL, HIGH-STRENGTH MAGNET - The neodymium magnet and silicone center create a strong grip and smooth glide when paired with Steelie Mounts or other metal surfaces
UNIVERSAL, SECURE ATTACHMENT TO PHONE OR CASE - The included Metal Plate with 3M adhesive secures to most any Apple iPhone, Samsung Galaxy, or Google Pixel phone, allowing multiple devices to work with the included Orbiter Magnetic Socket
WORRY-FREE GUARANTEE - all Nite Ize products are backed by our Worry-Free Guarantee
FOR MULTIPLE DEVICES AND MOUNTS - No need to buy a whole new Steelie Kit when you want to use your Orbiter Magnetic System on multiple mounts. Simply buy the Orbiter Magnetic Socket and you can extend the system for use with additional devices and mounts
COMPATIBLE WITH STEELIE PHONE MOUNTING SYSTEMS FOR HANDS-FREE VIEWING - The Orbiter Magnetic Socket magnetically connects your phone to Steelie Mounts like the Dash Mount, Windshield Mount, or Vent Mount (sold separately)
SAFE FOR USE WITH PHONES - The powerful magnet will NOT damage your mobile device. It can also be paired with GPS and MP3 devices. However, do not place it near magnetically sensitive objects such as credit cards, computer hard drives, or pacemakers
$234
Finally, I can use my phone cover without having to physically attach a magnet to it or attach any disgusting metal plates to it! I've had a Steelie mount for a while and am delighted with it, but ever since switching to wireless charging with my Samsung, having a magnet hooked to my phone has been a headache. I can carry this attachment with me whenever I need the magnet to attach my phone to something outside of the car, and it keeps the magnet in the car on the mount and off of my phone. This baby performs the job admirably; I've wasted plenty of time trying to jerryrig a similar solution just to have it fall apart when I needed it most. Nite Ize, thank you! You've done it once more!
4.2/5
✅ PREMIUM QUALITY - The Custom Auto Car Coin Organizer is constructed from premium quality materials to ensure maximum strength and durability for long lasting usage.
✅ VERSATILITY - The Custom Autos Car Coin Organizer can also be used at your office or at your home. With this, you can store and organized your cluttered coins and change.
✅ EASY TO USE - The Custom Autos Car Coin Organizer is easy to use, it has a different slot for different sizes of coins for your convenience. It can be installed via magnetic or hook and loop tape keeping it secure while driving or just put it anywhere you feel safe.
✅ DURABLE - The Custom Autos Car Coin Organizer is durably made of thick plastic material that ensures it capability to hold coins in a long period of time.
✅ PRACTICAL - The Custom Autos Car Coin Organizer is a very practical and convenient auto accessory that will holds your loose change in an organized manner, it is special design for coins storing and taking easily.
$234
I was disappointed that my current automobile doesn't have one because my first one had one built in. When I was at a drive-through or needed change quickly, I would take too long fumbling with a jar of change. This is quite useful. I use this at work because I'm a waitress as well, and it makes things a lot simpler so that I don't have to hunt around in my pockets for 43 cents. adore this I purchased it for a friend as well, and they gush about how much they adore it. Funny how tiny things can brighten our day.
4/5
Made in USA
Includes Upper Dash Panel & Phone / GPS Cradle Holder
Large Phone Holder
Easy Installation
$234
adore it 4 starsThe bottom kind of bumps on the center divider piece as you turn it from horizontal to vertical, especially if it's plugged in. Although it makes using touch ID on your phone a little cumbersome, it's not a problem if you keep your phone perfectly horizontal at all times. If you have a lifeproof or other robust case, this may fit snugly or not at all. This is pure speculation, and the reason I say this is because my iPhone 6 in a lifeproof case was using the largest "arm" arrangement possible (it comes with two options depending on size of your phone). I therefore have no idea how it would function with a plus.
4/5
Easy-to-clean with just soap and water.
STORAGE: The organizer keeps your items at your fingertips during your commute. Features additional mesh storage pocket on the front is perfect for loose change, small bills, or business cards.
ORGANIZATION: The Vent Catch-All holds your smaller, loose items, like sunglasses, cell phones and pens.
CONVENIENT: Two attachment accessories are included in each package and offer four hanging heights to fit your space.
$234
I wanted something in the front seat of my tiny car for rubbish, such as straw wrappers, post-it notes, and floss picks (yes, I'm that chick flossing in traffic; don't judge me!).Small rubbish fits perfectly in this. The clock is covered if I hang it from the center vent, and the radio controls are covered if I hang it from the other center vent. It can be slung over a side vent to cover the cup holders (previous receptacles for small trash...)It now hangs from the air intake sliding lever of the climate control and just covers the largely useless cup holders below it (my Honda has a LOT of cupholders for a car that only fits 5 small people).
3.6/5
〖LASTING DURABILITY〗 Made from ABS plastic with a matte finish.Waterproof and Mildew proof of material.Not easy to deform under pressure.
〖NON-SLIP〗 Non-slip, removable, rubber mat prevents items from sliding and rattling in the tray.
〖OEM FIT〗 The surface texture matches perfectly for your Tundra interior. And it looks like belong to the truck. New design for your Toyota Tundra.
〖SIZED TO PERFECTION〗 Dashboard organizer Fits for 2020 2019 2018 2017 2016 2015 2014 Toyota Tundra, Including SR, SR5, LIMITED, Platinum,1794 Edition and TRD Pro.MUST-HAVE Tundra Accessories.
〖NO DRILLING REQUIRED〗We recommend that you clean the surface of the dashboard with alcohol before installation,so the glue tape will better bond the surface.The same size as the original Tundra dashboard, no drilling required. Tearing the double-sided tape behind, and then it fits accurately.
$234
I recently bought the dash organizer for the center console, and it fits nicely there. I would advise anyone considering purchasing it to do so.
3.5/5
FOR MULTIPLE DEVICES: The adjustable phone mount kit includes a tripod stud, cellphone mount & a storage compartment to hold sunglasses & accessories. Compatible with GoPro cameras, POV cameras & other devices.
RUGGED RIDGE JEEP PARTS: Count on Rugged Ridge to provide you with proven Jeep parts & accessories like axles, lift kits, seat covers, wheels, brakes, floor liners & more for varying Jeep model types.
CATCH THE ACTION: Never miss action on the road or trails this with dashboard mount for phones. It features a universal ball mount & tripod stud so you can record, shoot, use GPS & more with more than one device
DASHBOARD PHONE MOUNT: The adjustable phone mount is a custom fit cradle that holds onto your device while hitting the trails & off roading. Mounts to existing screws & easily snaps into dash.
FIVE YEAR WARRANTY: Our Rugged Ridge products are covered by industry leading 5 year warranty & Rugged Ridge Floor Liners have Limited Lifetime Warranties providing customers with repair or replacements subject to certain common exclusions.
$234
The reviews are all accurate, but nobody really draws attention to all the crucial information that makes them easier to interpret. I'll do my best to fill that void.To begin with, this is a standard Rugged Ridge product. carefully thought out, expertly done, and reasonably priced. It's not necessarily garbage just because something is cheap. Simply said, it suggests that it might not be as sophisticated or as long-lasting as something constructed with different (more expensive) materials. In a moment, I'll explain what that implies.The dash kit without the phone holder that attaches on the ball is designated as 13551.11. I had to do a lot of searching to figure that out, so I want to save you the time. This also works perfectly on a 2016 Jeep Wrangler (Unlimited.) Speaking of fit, this is an extremely tight fit, and as other reviewers have noted, careful installation is required to prevent damaging the tray's edge. You must carry out either one (or both) of two actions in order to achieve it.The edges are firm and sharp enough to scratch off the softer plastic of the tray that is molded into the dash, but they are not "sharp" in the sense that they could cut you. You must avoid the first error I made, which was believing that this needed to be "levered" into place, if you want to prevent that. There isn't. It merely clicks into place. The bottom edges can be rounded using a reamer, file, or other tool, as several other reviewers have pointed out.If you don't want to, you don't actually have to do it, but you still need to pay attention. The bracket will simply snap into place if you remove the bolt as instructed, line the hooks up over the first two slots of the air vents, and then push down firmly (you may need to give it a little tap to urge it down so the hooks flex enough to extend past the edge of the vent). Once the bolt is in place and the cover is in place, the base's installation is finished.Regarding the mount itself, I may not have been particularly attentive, but there were a few features I hoped would function as I had anticipated but was unable to confirm before buying. It was fortunate that everything turned out just how I had hoped:You can use this to do precisely what I did and get rid of the Garmin suction cup mount and attach my GPS Map where I could see it easily because the ball mount is a 17mm or 1" ball, which is the same as Garmin mounts, the "typical" ram-line 1" ball, and many others out there. Although it is just a little bit looser than the Garmin one, it cannot move. Just somewhat less tightly.If the knob breaks off, as some of the other reviewers have noted, I'll update this review. We'll see if there is a problem with plastic aging in the sun since it was placed in August of 2016.Second, it's not evident how to attach an action camera or any other stud mount device from the image of the stud mound for a camera. The ball mount, the component with the brass (yellow) insert, and the piece with the larger hole are all different pieces, and the mount is actually made up of three pieces (not counting the bolt and tray). Depending on what you want to set up, you install them in various combinations. You may loosen and tighten the mounting pieces using a little thumb-wheel on the mount's base. Since it allows for the installation of additional items there, I view this as a HUGE positive!Overall, I'm extremely happy with this purchase and am considering purchasing this as a present for other JK and JKU owners I know!
3.5/5
Fits up to a 3.6 inch wide phone
Adjustable
Dash mount and Phone mount kit
Limited 5 Year Warranty
$234
The reviews are all accurate, but nobody really draws attention to all the crucial information that makes them easier to interpret. I'll do my best to fill that void.To begin with, this is a standard Rugged Ridge product. carefully thought out, expertly done, and reasonably priced. It's not necessarily garbage just because something is cheap. Simply said, it suggests that it might not be as sophisticated or as long-lasting as something constructed with different (more expensive) materials. In a moment, I'll explain what that implies.The dash kit without the phone holder that attaches on the ball is designated as 13551.11. I had to do a lot of searching to figure that out, so I want to save you the time. This also works perfectly on a 2016 Jeep Wrangler (Unlimited.) Speaking of fit, this is an extremely tight fit, and as other reviewers have noted, careful installation is required to prevent damaging the tray's edge. You must carry out either one (or both) of two actions in order to achieve it.The edges are firm and sharp enough to scratch off the softer plastic of the tray that is molded into the dash, but they are not "sharp" in the sense that they could cut you. You must avoid the first error I made, which was believing that this needed to be "levered" into place, if you want to prevent that. There isn't. It merely clicks into place. The bottom edges can be rounded using a reamer, file, or other tool, as several other reviewers have pointed out.If you don't want to, you don't actually have to do it, but you still need to pay attention. The bracket will simply snap into place if you remove the bolt as instructed, line the hooks up over the first two slots of the air vents, and then push down firmly (you may need to give it a little tap to urge it down so the hooks flex enough to extend past the edge of the vent). Once the bolt is in place and the cover is in place, the base's installation is finished.Regarding the mount itself, I may not have been particularly attentive, but there were a few features I hoped would function as I had anticipated but was unable to confirm before buying. It was fortunate that everything turned out just how I had hoped:You can use this to do precisely what I did and get rid of the Garmin suction cup mount and attach my GPS Map where I could see it easily because the ball mount is a 17mm or 1" ball, which is the same as Garmin mounts, the "typical" ram-line 1" ball, and many others out there. Although it is just a little bit looser than the Garmin one, it cannot move. Just somewhat less tightly.If the knob breaks off, as some of the other reviewers have noted, I'll update this review. We'll see if there is a problem with plastic aging in the sun since it was placed in August of 2016.Second, it's not evident how to attach an action camera or any other stud mount device from the image of the stud mound for a camera. The ball mount, the component with the brass (yellow) insert, and the piece with the larger hole are all different pieces, and the mount is actually made up of three pieces (not counting the bolt and tray). Depending on what you want to set up, you install them in various combinations. You may loosen and tighten the mounting pieces using a little thumb-wheel on the mount's base. Since it allows for the installation of additional items there, I view this as a HUGE positive!Overall, I'm extremely happy with this purchase and am considering purchasing this as a present for other JK and JKU owners I know!
The simple answer to this question is no, the police do not have to stop you for using a mobile phone. However, if they have reason to believe that you are using your phone in a way that is unsafe or illegal, they may pull you over. For example, if you are texting while driving, the police may pull you over and issue a ticket.
Most air vent phone holders on the market are made of high-quality, durable materials that are designed not to damage your phone. However, there are a few lower-quality air vent phone holders that can damage your phone's finish or scratch the screen. If you're concerned about damage to your phone, be sure to choose a high-quality, durable air vent phone holder.
Magnetic phone mounts use the power of magnets to keep your phone securely in place while you're driving. The mount attaches to your car's dashboard or windshield, and a metal plate attaches to the back of your phone. The magnets in the mount then hold your phone in place.
Attach the suction cup to the dashboard. Wet the suction cup with water. Press the suction cup against the dashboard.
To make suction cups stick permanently, you need to use a strong adhesive. Apply the adhesive to both the suction cup and the surface you want to attach it to. Press the suction cup into place and hold it there for a few seconds. The adhesive will set and the suction cup will be securely attached.
COPYRIGHT © 2019