Best Automotive Replacement Clutch Linkages in 2022

Last update: December 7, 2022

Can you drive a car with a broken clutch cable?

A broken clutch cable may prevent you from shifting gears, which can make driving a car with a manual transmission difficult or impossible. In some cases, you may be able to drive a car with a broken clutch cable by shifting gears without using the clutch pedal. However, this can damage the transmission and should only be done as a last resort.

How do I know if my linkage is bad?

If your linkage is bad, it will likely cause your car to have steering problems. The most common symptom of a bad linkage is that the car will pull to one side when you turn the steering wheel.

How do you know if your clutch cable has gone?

If your clutch pedal feels spongy or you have to press it all the way to the floor to engage the clutch, your clutch cable may be to blame. A broken or frayed cable will need to be replaced.

How long does a clutch last once it starts slipping?

The average clutch will last anywhere from 40,000 to 60,000 miles before it starts slipping. However, this number can vary depending on the make and model of your vehicle, as well as your driving habits. If you are someone who frequently uses your clutch to drive in stop-and-go traffic or up steep hills, you can expect it to wear out sooner than someone who uses it less frequently. Additionally, if you regularly ride your clutch while shifting gears, this can also cause it to wear out more quickly.


APDTY 141607 Shift Cable Bushing (Allows Repair Instead Of Cable Replacement) Review:


While it was in drive, the shift cable broke. refused to enter the park. I placed the order, received it a few days later, and mended it in ten minutes. worked perfectly. Fixing the shift cable was simpler than disassembling the dash. I drive a Toyota Sienna from 2004. You can alter it using a lot of the videos on YouTube. One in particular demonstrates how to disassemble "THE ONLY NECESSARY" dash components. It was all done by me, a 57-year-old woman. It's doable by anyone.



Bushing Fix BP1Kit - Transmission Shift Cable Bushing Repair Kit Review:


This bushing served its purpose. The van belonging to my wife was stuck in drive and would not change into any other gear or park. After conducting a Google search, I came across a YouTube video detailing this very same problem and providing a fantastic guide for removing the lower half of the dash to access the transmission cable and bushing.Although getting to the bushing took a lot of time, it was fairly simple to install. The elements of a Toyota dash must be removed in the proper order in order to avoid damaging the panels, just like when putting together a challenging puzzle. I would have included a link to the video on this review, but I'm afraid Amazon will either delete the link or block the review. You can discover the video by searching for "Sienna 2004 Stuck in Drive."Due of the bushing's astronomical price, I only awarded it four stars. However, this is a lot better value than driving your car to Toyota and paying them $500 to replace the shifter cable and bushing.



Bushing Fix F2KIT1 - Transmission Shift Cable Bushing Repair Kit Review:


Fantastic. On a 2000 F250 7.3 PSD with the 4R100 trans, I had a worn-out old bushing that I had zip-tied to the trans input lever. This replaced it. Combine this installation with the customary use of a Dormant piece to replace the shift tube entirely underneath the steering wheel column. These seem to need replacement every 300,000 miles or so. Fortunately, if you've done it previously, the entire job—including installing the shift tube in the cab—takes less than an hour.



Dorman 600-602 Shift Linkage for Ford Truck 4WD Review:


For my 1997 F-250HD, I bought and fitted this shift linkage, and it fit perfectly. Considering that a new linkage was dealer only till a few years ago, this is a very good value. A 1" box wrench or a T55 torx bit are required tools to remove/install the pivot bolt. I used the box wrench to replace the component.Save time by removing the shift linkage plate from the transmission first by removing the two bolts holding the plate on if your linkage has already broken off. Once it is out from under the truck, you may remove the old pivot bolt from the plate. Since the linkage will obstruct access to the two bolts holding the plate on, you must reassemble the vehicle by bolting the plate back on before attaching the new linkage.



BushingFix TB1KIT9 - Transmission Shift Cable Bushing Repair Kit Review:


You get into the same car you drove without incident that morning after work. You want to go home because you're exhausted. When you turn on the automobile, press the brake pedal, and shift into reverse, the transmission does not engage. Your initial thought was, "Oh no, money." The transmission, though, is still in park, as you later discover. You make a few movements up and down "the column." No joy yet. However, you see that the shifter's resistance is lower than usual, so you conclude that the problem must be with the linkage and not the transmission. A positive sign is that there is no trouble light.You therefore wonder if the shift cable may have snapped. Most likely not, as wires don't break all that frequently and you didn't feel a snap. Realizing that the issue most likely stems from a connection that has gone loose, either to the shifter itself or to the transmission shift lever (a little "L" that protrudes from the transmission), the shifter. While driving, you pull up the shifter housing and watch the cable even though it's probably the latter. It moves with the shifter, thus the gearbox must be the source of the issue. Upon opening the hood, you may see that the shift cable end has come loose from the transmission shift lever if you check behind and beneath the air intake (feed). Once you arrive at your destination, you slide the engine back on for just long enough to put the car in park before sliding it back on once more (with the engine now off).This is a simple fix that will cost your neighborhood shop maybe $100. Wrong. mainly because the majority of auto manufacturers don't make replacement bearings for these assemblies. Just the tiny piece of plastic that twists in the cable-end housing to keep the cable on the transmission shifter and allows it to move in an arc is worn out; the bearing is the only other component. It turns out that your favorite automaker and dealership want to replace the complete cable assembly, which will cost $500 to $600.There must be a better way, and now there is due to a small business called Bearingfix (as I discovered). You can easily fix this yourself in 5 minutes with this small part. Due to the fact that you do not need to remove the air intake/cleaner to complete this, it is even simpler than most YouTube tutorials show (at least on my car). I was amazed at how easy this was on my 2008 Chrysler.Even though it will take a few days to get this thing mailed to you and the price (including delivery) is a bit high for a small piece of plastic and a plastic installer, it sure beats a tow and a $600 repair cost.Recommended!By the way, individuals who are giving this product bad reviews appear to have installed the component incorrectly and ruined it. The installation guidelines are easy to understand.



BushingFix HR1KIT1 -Jeep Transfer Case (4X4) and GM Transmission Shift Cable Bushing Repair Kit. Fits Select Vehicles See Listing for Details. Review:


I was able to save hundreds of dollars by ordering this part from Amazon! When the tow truck driver described to me what they thought the problem was, the linkage connecting my daughter's jeep to the transmission became separated. I sought for the part on Amazon and was able to replace it for the price of the part.


How long does it take to change a clutch plate?

How much does it cost to fix a clutch linkage?

If the clutch linkage needs to be repaired, it will cost between $200 and $600. The cost will depend on the severity of the damage and the make and model of the vehicle.

Is a clutch cable easy to replace?

A clutch cable is not difficult to replace, but it is a little time consuming. The first thing you need to do is remove the battery and disconnect the negative terminal. Next, remove the air filter housing and disconnect the mass airflow sensor. Now, remove the engine cover and disconnect the throttle body cable. Then, remove the intake manifold and disconnect the fuel injectors. Finally, remove the clutch cable from the transmission.

Is it worth replacing clutch on old car?

If your car is more than a few years old, it might be time to start thinking about replacing the clutch. A worn-out clutch can cause a number of problems, from making it difficult to change gears to causing the engine to stall. Replacing a clutch is not a cheap repair, but it is usually worth the money to keep your car running smoothly.

What are clutch linkages?

What are the 3 major components of clutch?

A clutch is a device that is used to connect and disconnect two rotating shafts. It is usually used to engage and disengage the engine from the transmission. The three major components of a clutch are the pressure plate, the clutch disc, and the throw-out bearing.