Best Automotive Fender Flares in 2022

Last update: November 29, 2022

Are fender flares legal?

Fender flares are aftermarket car parts that attach to the fenders of a vehicle. They are usually made of plastic or fiberglass and extend outwards from the fender, away from the body of the car. Fender flares can serve a few purposes. Some people believe that they make a car look more aggressive or “tough.” Others believe that they improve the aerodynamics of a car or truck. And still others believe that they serve as a way to protect the paint on a car’s body from being chipped by rocks or other debris that gets

Are fender flares worth it?

Fender flares can definitely be worth it, especially if you are trying to achieve a certain look for your vehicle. They can also be beneficial in protecting your paint from chips and debris that can be kicked up while driving.

Can fender flares cover rust?

Fender flares can cover up rust on your vehicle. Rust is unsightly and can decrease the value of your vehicle. Fender flares can give your vehicle a fresh, new look while protecting it from further rusting.

Can you put bigger tires on truck without a lift?

You can put bigger tires on your truck without a lift, but it may not be the best idea. Bigger tires can throw off your truck's handling and make it more difficult to control on the road. If you do decide to put bigger tires on your truck without a lift, make sure you get the right size tires and that they're properly inflated.


Tyger Auto TG-FF6D4198 For 2002-2008 Dodge Ram 1500; 2003-2009 Ram 2500 3500 (ONLY Fit 6.5' Truck Bed) | Paintable Fine-Textured Matte Black Factory Style Fender Flare Set, 4 Piece Review:


Fantastic flares like this. With the included hardware, installation was simple, and I love the way they look! They gave my 2003 Dodge Ram enough covering to cover up the "fender rot." I gave the sections a thorough layer of Rust-Oleum after sanding them down. These were quickly installed by me on my own. All other screws were placed in the factory holes, though I did drill one hole on each rear to help tighten them up a little. They didn't come with a rubber seal, but they fit just fine without one.



Fender Flares for 99-06 Chevy Silverado, Sierra, Avalanche, Yukon, Suburban (Pack of 4) OE Style Wheel Fenders Flare Truck Accessories Best for Chevrolet GM GMC Pick-up Trucks Re-Paintable Trim Guards Review:


Excellent fit and appearance. junk hardware for fasteners. replacement fasteners were purchased at Oriley's auto parts. after snapping the first few fasteners that were provided.Overall, the price of fasteners at the neighborhood auto parts shop was the same as the price of the initial order. Although it may seem frustrating, after my trip to the autoparts shop, the final cost came to roughly $100. The cost of the following reasonable choice was at least $200.I believe sacrificing a little frustration, I managed to save $100. If I had known beforehand, I would have purchased the exact same kit and would have skipped wasting time on the fasteners that came with the fenders in favor of buying only good fasteners.



Premium Fender Flares for 2002-2008 Dodge Ram 1500; 2003-2009 Dodge Ram 2500 3500 (Fit Fleetside Models) | Fine-Textured Matte Black Pocket Bolt-Riveted Style 4pc Review:


It would have been good if I didn't had to screw every single rivet on myself as they are simply decorative. I would have preferred that they were completely absent from the aesthetic, but I was unable to locate any flares without any sort of rivet pattern.Since the accompanying metal clips were mostly useless, I did need to drill a couple holes over the rear. However, the finished product looks fantastic and covers up all the corrosion I had on the back wheels.One installation tip: Make sure the rubber strip's sticky side is facing the flare when you attach it. The reason being that the rear flares' sharp creases and corners may protrude slightly if you don't. Not particularly obvious unless you're paying close attention.



Tyger Auto TG-FF6C4218 For 1999-2007 Chevy Silverado/GMC Sierra (2007 Only fit Classic Models) | Textured Matte Black Paintable Factory Style Fender Flare Set, 4 Piece Review:


For only $89, these fender flares are truly incredible. They have been on my truck for about four months now during the winter in Maine, and so far the finish has been flawless. I installed them as they were shipped, I didn't paint them. One feature that I really like about them is that they extend all the way underneath the fenders, where the rocker panels are located, covering the rust damage that other fender flares would not. My only issue is that, as some other reviews have said, the front passenger side fender flare sticks out somewhat in the front, but overall for only $89, I'd still give them easily a five-star rating. Even though these are a high-quality product, a single GM fender flare costs more than the full set. I'd unquestionably purchase these again.



YITAMOTOR Steel Fender Flares Kit for 2007-2018 Jeep Wrangler JK (2/4 Doors), Heavy-duty Solid Steel Off-Road Fenders for Jeep Unlimited JK Front Rear Flat (4pcs) Review:


Here is my evaluation I was worried about how it would appear on a basic Jeep. In the pictures, there wasn't much to relate to.I should have waited a few days and purchased the suggested tool from Amazon since I didn't have it, but who has time to wait when you have something new to try out on your jeep?To install the screw rivets, I utilized the bolt they provided along with a wrench and socket. This process took a good hour and a half, and it was really time consuming. I installed all but two rivets, but even with those two missing, I don't think the integrity has been affected in the slightest. They look excellent, feel durable, and offer a reasonable price.In order to fit in and not stand out, I did make sure to paint the brackets on the front two fenders black.A 3 hour install all in all.I hope this is useful to any of you with factory tires and lift.



Trim-Lok Fender Flare Edge Trim – EPDM Rubber Trim for Car and Truck Wheel Wells – Bonds with 3M Automotive-Grade Tape – 0.227” Height, 25’ Length Review:


I purchased this item to repair the fender flare pads on my 1998 4Runner Limited (the rubber strip between the flare and the body). To paint the flares, I removed them. purchased 25 feet, more than enough to line the flares that were in need of it. worked perfectly. To acquire the appropriate angle, you'll need to experiment a little with how you fasten the edge trim to the flare. When you install the flare, there will be a gap between this trim and the body if the angle is off. When you install the flare, the trim should look excellent and fit tightly against the body if the angle is perfect. The flare, not the body, is where the trim adhesive is attached. Two-sided tape is not necessary.I started by cutting the rope to length. I started by removing an inch of the red tape covering the glue on one end. After that, I carefully pushed down on the rubber trim piece to ensure that it seated all the way on the edge of the flare. Be tolerant. It requires time. When installing the flare, the trim should be flush against the body at the proper angle. When I was satisfied with the trim's angle and location (nice and straight), I peeled and removed the remaining red tape to reveal the adhesive and pressed the trim down once more. The rubber trim can be pulled up and reattached even if you make a mistake and don't get it right the first time. Simply said, it will be more difficult to seat the trim with the adhesive showing. I suppose you may reattach it after replacing the red tape that covers the adhesive. Or simply use a fresh piece. It is best to create one flare, install it, and then learn from your errors. You have extra room of 25 feet in case you wish to retry a few flares. In case you need to remove the flare and restart, make sure you have lots of extra clips (yellow and white). They snap easily.There is a piece of trim that goes under the doors if you, like me, are replacing your running boards. For these two pieces, left and right, I used the previous pads once again.0.227" Height, 25' Length Trim-Lok Fender Flare Edge Trim - EPDM Rubber Trim for Car and Truck Wheel Wells - Bonds with 3M Automotive-Grade Tape



G-PLUS 4PCS Black Universal Wheel Fender Flares Flexible Durable Polyurethane Extra Wide Auto Car Body Kit Review:


The fenders arrived in fine condition and without any scratches, though I had already planned to paint them. The JDM Kei Van for which I had ordered them turned out to be too big for them by approximately 1" (25mm), and they would have wrinkled if bent to suit the wheel-well opening. Since this is a very modest application, I'm convinced that these will fit any small- to medium-sized car and wheel-wells (kei automobiles are tiny and use factory rims that are between 12 and 14 inches in diameter). The cloth appears to be of high quality and has decent flex while preserving a solid shape. With the proper paint and procedure, these would also paint up nicely. They are an excellent value and I want to utilize them on a future project, so all in all a nice product!



G-PLUS Fit for 07-13 Chevy Silverado 1500/07-14 Silverado 3500HD 3500HD (Standard Bed 6.5ft & Long Bed 8ft) | Textured Black Pocket Bolt-Riveted Style Wheel Fender Flare Set 4 Pieces Review:


You receive the plastic of the quality you paid for. However, it's not all that horrible. Make sure the flare is sitting on a small moving blanket or anything soft when you put the fake bolts together because it gets very easily scratched. It took ages to install. The directions are utterly useless. A lot of things I had to wing. Overall though, they're on my truck. There have been two months and a few brief, trouble-free road trips.



For 99-06 Chevy Silverado/GMC Sierra Factory Style 4pcs Paintable ABS Smooth Wheel Fender Flares (Black) Review:


These fender flares are stylish and simple to install. They hide the severe rust that the wheel wells of Chevrolet pickups are notorious for. They blend in nicely with the trim on my 2000 Red Chevrolet 1/2 Ton. No huge deal, you'll need to drill a few holes. For a good installation, I would drill a few more holes than the flare has. In a few holes (wheel well arches in particular), try using these plastic fasteners instead of the ones that are given. For the additional holes you might drill: Ford, GM, and Chrysler Hole Retainer, 6.4 mm (Qty: 100) 2000T Gripper Box



OE Style 4Pcs Wheel Fender Flares for Chevy Silverado 1500 2500HD 3500HD 6.5 & 8.1 feet Bed Standard/Extended Cab 07-14 Review:


The backs had difficulty installing because they seemed to be a little bit too long and required additional drilling to mount them, leaving gaps, but I suppose that's to be expected when you don't get top-of-the-line equipment. Eventually, more bolts were added until the gaps closed up even more, making them less noticeable now. The fronts were the easiest to install because they fit right up to factory holes.


Can you put fender flares without bolting?

You can put fender flares without bolting them on, but they may not stay in place as well. It really depends on the type and design of the flares. Some have clips or other fasteners that help keep them in place, while others are meant to be bolted on. If you're not sure, it's probably best to err on the side of caution and bolt them on.

Do fender flares allow for bigger tires?

Fender flares are an easy way to add style and functionality to your truck, jeep, or SUV. They give you the ability to run larger tires and wheels while protecting your paint from road debris. Most fender flares on the market today are made from durable UV resistant materials that will not fade or crack over time.

Do fender flares help with mud?

Fender flares can help to some extent with mud but they are not a cure all. Mud can still splash up on to the sides of the vehicle and get caught in between the fender flare and the body. In addition, fender flares can actually make it more difficult to clean the mud off of the vehicle since they provide another surface for the mud to adhere to.

Do you have to cut fenders for fender flares?

No, you do not have to cut fenders for fender flares. Fender flares can be installed without cutting the fenders.

How do you fit bigger tires without lifting?

If you want to fit bigger tires without lifting, there are a few things you can do. First, you can try trimming the fenders. This will give you some extra room to work with. You can also try using wheel spacers. This will help to push the wheels out and give you more room to work with. Finally, you can try using a body lift. This will lift the entire body of the vehicle up, giving you more room to work with.

How much does it cost to have fender flares installed?

Adding fender flares to your vehicle can give it a more aggressive look, while also providing protection from debris and mud. But how much does it cost to have fender flares installed? The cost of having fender flares installed will vary depending on the type of flares you choose and the vehicle you drive. Expect to pay anywhere from $200 to $1,000 for the parts and labor. If you're looking to save money, you can always install the flares yourself. But keep in mind that it's not a simple task. You'll need to drill into your