A torque angle gauge is a tool that helps you measure the amount of torque, or rotational force, being applied to a bolt or nut. It is used to ensure that the proper amount of torque is being applied so that the bolt or nut is tightened correctly.
There are a few different ways that we can measure angles. The most common way is probably with a protractor. We line the protractor up so that the baseline is flush with one of the lines forming the angle, and then we read the degree measurement where the other line intersects the protractor. Another way to measure angles is with a ruler and a compass. We draw a circle with the compass, and then use the ruler to draw a line segment from the center of the circle to the point on the circle that forms one endpoint of the angle. We then use
There are a few ways to find the angle between two walls. The easiest way is to use a protractor. Place the protractor flat against the wall and line up one of the arms with one of the walls. Then, use the other arm to line up with the other wall. The angle where the two arms meet is the angle between the two walls. Another way to find the angle between two walls is to use a tape measure. Measure the length of one wall, and then measure the length of the other wall. The angle between the two walls is equal to the
There are a few different ways that you can measure an angle without using a protractor. One way is to use a ruler to measure the length of the line that forms the angle. Then, using a calculator, you can divide this length by the length of the line that forms the other side of the angle. This will give you the tangent of the angle, which you can then use to find the angle's measure. Another way to measure an angle is to draw a line that is perpendicular to one of the sides of the angle, and then use a ruler to measure the length
4.5/5
AAA batteries for super long life
Flip-up display for easy viewing from any position
Hold feature allows you take a reading and hold the value while you move the gauge to a new position
The machined aluminum base imbedded with high strength magnets sits perfectly flat for optimum accuracy and has a built in V groove for use on pipes or conduit
Built-in level display using Dead Level Technology TM is always visible and permanently stored
$234
I primarily bought this angle gauge to verify the table saw's blade angle. Since I cut segmented miters frequently, precision is crucial. When the gauge arrived, I unpacked it, quickly glanced over the directions, zeroed it out, and checked that the blade angle was exactly 90 degrees. I then used the saw guide to set my blade to 45 degrees, and I was able to tell by using the gauge that the guide was wrong by half a degree. The same was done for 22.5 degrees. Now that I have this gauge, I will be able to consistently acquire the precise cuts I require. Definitely worth the cost. Would I suggest it? Absolutely yes.
4.4/5
ã€Great Repeatability and Consistency】This angle gauge is designed with accuracy of ± 0.2° and the resolution is 0.1°. The measuring range: 0 to 360° (4*90°). Display unit: DEGREE only. It provides convenience in woodworking, construction, machinery, telecommunications, automobile etc. It is pre-calibrated in factory.
ã€Easy Battery Installation】You can install battery easily and need no screwdriver. WIth only one AAA battery, the digital angle gauge works 50 hours averagely. *Automatic shut-off after 5 minutes.
ã€Strong Aluminum Framework】The digital angle gauge applied sturdy aluminum alloy instead of plastic for the main framework. It’ll provide years’ usage.ã€Two Measuring Mode】①Checking the true level. â‘¡Checking the relative angle between two surfaces.
ã€Lower Power Reversible LCD Display with ERROR indicator】 The Digital Angle Gauge has a large LCD display with backlight, which only needs one battery for providing accurate, quick and clear measurements and even you can easily read in dark environment. If the digital angle gauge is used in an incorrect position (e.g. tilts diagonally over 30 degree), display will tell ERROR to make sure that use is getting the accurate measurement.
ã€Packing contains】Digital angle gauge*1, 1.5V Alkaline battery*1, storage pouch*1, instruction*1
$234
Level accuracy is very significant. Although I do value the 0.05 degree precision at 0 and 90 degrees, you should be aware that the accuracy at "other" angles is 0.2 degrees.Update: This level functions perfectly. Because it is recessed and tilted, the display is simple to read from a variety of viewing angles. Since the screen won't be as easily scraped as if it were flush with the frame, this also offers protection. Additionally, a button press turns the light on or off, and it stays on if you choose. Magnets are also incredibly powerful. Furthermore, readings update almost immediately. Additionally, battery changes are simple. And lastly, it has a useful carrying case. It is therefore incredibly user-friendly, portable, and robust. I wish the box had said that it was accurate to 0.15 or less at "other" angles. I will hold onto this level and exchange it for a digital inclinometer in the same price range. Cleaning mortar or something like would not be simple, in my opinion.
4.4/5
$234
I have the Wixey version of this program, so I though some comparison notes could be helpful. Most significantly, the IGaging unit performs admirably, though I'll let others make more exact accuracy comparisons. Absolute level performance is advantageous, and it's what convinced me to switch brands. Though it is also practical, I haven't missed the three-magnet setup.My primary issue is that replacing the battery on an iGaging is far more difficult and requires removing four tiny, loseable screws. Although a proper (but tiny and lose-prone) screwdriver is offered, I long for the Wixey's ease of opening with a dime or a fingernail. The 9-volt battery in IGaging will undoubtedly live longer, but button batteries are so inexpensive that it doesn't really matter.The thing I want most in a device is a backlight so I can read the display, but neither device offers it. iGaging would succeed if a backlight was powered by that 9-volt battery.
4.4/5
Clear digital readout provide quick, easy and reliable measuring for your work.
Battery included
Package include 1*GemRed 82412 digital angle gauge and 1*GemRed digital depth/height gauge
Working temperature: -10 ℃~+50℃
Widely used in woodworking, construction, machining, home decoration etc.
$234
The GemRed 82418 Digital level is being reviewed for the first time.I became interested in digital levels after viewing footage of "Project Binky" from Bad Obsession Motorsport on YouTube. I chose this model over the cheapest one because of the high quality of the reviews and the IP67 water and dust resistance rating. After owning it for less than a week, my initial impressions are excellent. It has exceeded my expectations, especially in terms of construction quality. To show a plastic and cardboard insert type packaging that opens without the need for a knife, a subdued white shipping box with black and red lettering and an engineering-style picture of the level opens (so much better than the sealed-to-within-an-inch-of-its-life alternative!)The box includes the essentials: a level (wrapped in bubblewrap), a straightforward nylon storage case or sleeve, an instruction leaflet (my copy was tucked inside the nylon sleeve), and three inexpensive AAA batteries. Not that it bothers me, but my level is silver rather than blue like in the image above. It seems nicely crafted and has a good weight in the hand. The level will be protected by the rubberized end caps in the event that it is dropped, which is likely to happen because the base's magnet cannot stably sustain the level's weight (more on that later).Simply unscrew the little round cap on the end, insert the three batteries (orienting them according to the level's description), and watch the screen to see the level come to life.The instruction manual is written in acceptable English, as opposed to the cryptically evasive and somewhat understandable versions you typically receive with products made in China (as this is). It describes the fundamental operations, the key features, how to use them, and how to calibrate the level if necessary. Even though the cardboard insert refers to the rubberized end caps as being "anti-falling," it is more than adequate and covers all the essential functions (that I can see) on a single page, despite the occasional spelling error and missing term.Let's talk about the problematic magnet. If not to enable you to attach the level to a magnetic surface and release it, why would you include such a thing in the device? I believe the issue is caused by the magnet being enclosed in the (aluminum?) housing and unable to adhere directly to the target surface. The window next to my desk has a metal frame, and when I place the level against the side of the frame with it pointing vertically up and down, it makes a quiet clink as it flimsily attaches itself to the frame, but it will slide down the frame until it catches on an imperfection in the paint (possibly), at which point it holds itself ready, waiting to fall when you aren't looking. Try attaching it to the inside of a metal pipe; it might or might not hang there, usually until you turn your head away, at which point it might fall to the ground inconveniently. Just keep in mind that it is dust and water resistant but not impact resistant (although those "anti-falling" rubberized end caps will help a little).I have not yet put the waterproof rating to the test, but according to IP67, the level should be able to withstand still (not moving) water for up to 30 minutes at a depth of less than one meter. I'm intrigued to try it out since if it doesn't work, I can return it and hunt for one with a stronger magnet. If it does survive, I might decide to keep it instead of looking for a better-sticking replacement when I absolutely need one.Overall, I believe I enjoy this product, primarily because of how well-built it feels in my hands. If I change my mind, I will update this review.
4.3/5
STRONG MAGNETIC BASE -- with its powerful magnetic base, this digital protractor can easily and firmly attach to miter saw, band saw, and table saw blades. You can also use it on fences, tables, and any other metallic surface. Thanks to its strong magnet, you no longer have to worry about holding the tool in place while taking measurements.
PROTECTIVE POUCH -- with your order, you’ll receive the AccuMASTER digital level with AAA batteries as well as a protective Pouch with a belt loop. Now you can keep your inclinometer and angle device within reach at all times, no matter where you are. It’s especially useful for completing work on a ladder, roof, or other precarious positions.
DUAL FUNCTIONALITY -- this tool can be used as both a bevel gauge and a digital level for carpentry. As a bevel gauge, it measures angles for woodworking. The AccuMASTER is compact, allowing it to fit into tight spots so you can get measurements you need to Perfect your project. It can also be used in welding, fabrication and even automotive tire alignment
CERTIFIED IP54 rated -- this woodworking tool is IP54 dust and water-resistant so it can be used in any professional woodshop, Garage, or backyard shed. This measuring accessory is just what you need to go from a novice woodworker to a master carpenter. No matter your experience level, This tool will help you complete any project.
EXACT & EASY TO READ -- the AccuMASTER' s bright backlit Stay glow(tm) display will never leave you in the dark and features large numbers, making it easy to read. No more eye-balling important measurements — this handy tool gives exact numbers so you can make the most precise of cuts with confidence. Its improved MEMS sensor increases battery life so it’s always ready for use, No matter how long it’s been in the tool drawer.
$234
The shop should add this quick and precise tool. Due to the accuracy this instrument provides, I must admit that trying to level my work tools and surfaces has driven me mad. Adjusting the HF drill press table took about 10 minutes (no surprise here). I appreciate the lighted, easily readable numbers, but the arrow that shows which way anything must move to be level is the best. I would suggest this to my friends and joke with them about how having a bit unlevel kitchen island didn't bother you before you got this incredibly precise measuring tool.
4/5
WIDE APPLICATIONS – Great tool for automotive, wood & mechanical industries, machinery, medical fields and etc
V GROOVE BASE – The V Groove base with strong magnets enables strong attachment over a curve or cylindrical magnetic surfaces such as metal pipeline or shafts
ABSOLUTE & RELATIVE MEASUREMENT – The regular absolute measurement mode can only measure the angle against horizontal plane. This tool also features with relative measurement mode for quickly measuring angle between two measured surfaces.
USEFUL 3-IN-1 DEVICE WITH BACKLIGHT – This newest digital gadget features with protractor, angle finder and level in one measuring tool. Backlight helps you to work at dark condition.
CONVERTS ANGLE TO OTHER UNITS : Conversions between : 4 x 90Ëš m/m : 1000mm/m, % : 100%, in/ft : 12in/ft. No more guessing or fuzzy conversion!
$234
I bought it so I could put air springs on my automobile. Because they were fitted improperly and were rubbing against the shock absorber, the air springs installed by the dealer were damaged (obviously after the warranty expired). The mounting bolts should only be tightened after lifting the wheel assembly until the "rear axle is at -1.2 degrees," according to the manufacturer's instructions. I according to the manufacturer's instructions and utilized this tool to position the axle perfectly in accordance with the specifications. Surprisingly, there is good space between the air springs and the shock. I was able to place the tool directly on the axle for an accurate reading, as seen in the picture, thanks to the grove and the magnet on the tool's bottom. Excellent gadget that is also useful for many other projects at home.
3.7/5
ã€DXL360S】â¤â¤High accuracy ±0.05, high resolution 0.01°. V Shape metal case for easy to fit at the corner or pipe.
ã€5 Sides】â¤â¤Magnetic base, audible alarming at settable angle range, any angle measurement, measure the angle between two faces, not only in earth gravity direction
ã€Charge】â¤â¤The unit could be charged by connecting the USB cable to the unit and a computer's USB port.
ã€Axis】â¤â¤Dual and single axis with user friendly LCD display angle. This unit can’t be connected to PC.
ã€Application】â¤â¤Interior decoration, Construction area, Plumbing, Floors & Stairs, Woodwork.
$234
Although I didn't anticipate using it much, I found it to be really helpful for situating pieces before I screw, weld, or fasten tools and setting up work areas.
There are many different ways to find angles using two angle gauges. The most common way is to use a protractor and a ruler. Place the protractor on the line you want to measure and line up the zero mark with the end of the line. Then, use the ruler to find the other end of the line and mark it. The angle between the two marks is the angle you are looking for.
There are many devices used to measure angles, but three common ones are a protractor, a theodolite, and a clinometer. A protractor is a simple, hand-held tool used to measure angles. A theodolite is a more sophisticated instrument that is used to measure both horizontal and vertical angles. A clinometer is used to measure angles of elevation or depression, such as the angle of a hillside.
An angle gauge is a tool used to measure angles. It can be used to measure the angle between two lines or the angle of a corner. Angle gauges are used in engineering and construction.
There are many instruments that can be used for measuring angles. Some common ones are protractors, inclinometers, clinometers, sextants, and theodolites.
There are two grades of angle gauges: the standard and the fine. The standard angle gauge is used for measuring angles up to 45 degrees, while the fine angle gauge is used for measuring angles up to 1 degree.
A surface gauge is a measuring instrument that is used to determine the flatness of a surface. The gauge consists of a flat plate with a graduated scale. The plate is placed on the surface to be measured and the reading on the scale is noted.
COPYRIGHT © 2019
